Leaders say Europe's waste-recovery goal is achievable

Published: February 7, 2012 6:00 am ET

Related to this story

Topics Packaging, Sustainability, Public Policy, Materials, Recycling, Suppliers

BRUSSELS (Feb. 7, 1:15 p.m. ET) — The European plastics industry has set an ambitious target: total elimination of plastics waste going to landfills by 2020. PlasticsEurope, with the support of other representative bodies, declared the industry’s intent last year when it called for a Europewide landfill ban.

Wilfried Haensel, executive director of PlasticsEurope, said: “Eliminating landfill in all European countries is far from being an unrealistic goal. Frontrunner countries have reduced landfilling of plastics waste to almost zero, with significant environmental benefits.”

Europe’s combined rate of recycling and energy recovery from plastics waste in 2010 was 58 percent. There is a significant way to go to reach the target rate of 100 percent, and this prompts some questions: How will the goal be achieved? How do you overcome obstacles such as the widely different rates in European countries?

Ton Emans, recently elected as president of EuPR, the Brussels-based plastics recycling organisation, told European Plastics News: “This target is ambitious but can be achieved with appropriate changes in waste management.

“For instance, we should have harmonized policies across Europe and should generate well separated streams in order to have quality input for plastics recyclers. These important changes will permit the growth of Europe’s resource efficiency, create a substantial number of jobs and reduce CO2 emissions thanks to the reuse of recycled plastics.”

There has been a historical lag between the best and worst European countries for plastics recycling and recovery. There has been improvement in the past two years, and the rate increased from 54 percent in 2009 to 58 percent in 2010.

In packaging, figures for 2010 released by the European Association of Plastics Recycling and Recovery Organizations (EPRO) showed that 16 nations recycled more than 30 percent of its plastic packaging waste in 2010. But Bulgaria, Greece, Cyprus and Malta were still lagging with rates below 22 percent.

Harmonization and better enforcement of EU waste directives would close the gap. PlasticsEurope is calling upon policy-makers in all countries to support better waste structures that replicate the success of Germany, Denmark, Sweden and Austria, where significant landfill restrictions have been put in place.

As well as policy, there are obstacles in the recycling industry that need to be overcome. Jan-Erik Johansson, PlasticsEurope’s resource efficiency program director, says there are challenges in various areas. There should be a drive towards collecting all plastics for recycling and recovery. At the reprocessing stage, a focus on quality would help to target used plastics into the right applications. End use markets for recycled products also need to be developed.

Johansson said that in the tough economic and financial climate, support needs to be given by governments and institutions to stimulate further recycling and recovery.

“A common roadblock is access to financing for the infrastructure needed to capture the value in the plastics which is currently disposed in landfill - estimated to be 8 billion euros per year for the EU27 plus Norway and Switzerland,” he said.

There is clearly a lot of work to be done between now and 2020. Knowledge transfer is an important tool, and PlasticsEurope runs a project with the plastics industries in France, Poland, Spain and the UK with the objective of accelerating recovery improvement.

Reaching the 2020 target will be a tough job. But the success of the Vinyl 2010 program shows that cross-border efforts in plastics recycling can indeed achieve desirable results.


Comments

Leaders say Europe's waste-recovery goal is achievable

Published: February 7, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Producers urge booming Brazilian housing market to use EPS

April 18, 2014 1:08 pm ET

Leaders in Brazil's plastics industry are asking lawmakers to mandate the use of expandable polystyrene (the raw material for expanded EPS) in new...    More

JM Eagle reopens shuttered Colorado plant with 8 PVC lines

April 18, 2014 1:02 pm ET

JM Eagle has reopened its Pueblo, Colo., plant with eight PVC pipe extrusion lines back in operation following an 18-month shutdown.    More

Image

'Thermoforming has nearly limitless possibilities'

April 18, 2014 12:54 pm ET

Julie McAlindon of PolyOne Corp. speaks about the future of thermoforming and the integration of Spartech Corp.    More

Image

Ascend targets nylon for auto applications, opening propylene monomer unit in Texas

April 18, 2014 10:57 am ET

Materials firm Ascend Performance Materials Inc. is in full operation at its new nylon 6/6 compounding line in Florida and will break ground by the...    More

Dutch company launching $100 million PP, PE recycling plant

April 18, 2014 10:42 am ET

Quality Circular Polymers is building a new plastics recycling operation in Geleen, the Netherlands' Chemelot industrial chemical site, with a capacit...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report provides analysis and discussions of economic and political conditions, market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as strategies being implemented by thermoformed packaging companies. In addition, there are reviews of 25 leading thermoformers in the packaging segment, assessing their growth initiatives and performance metrics over 10 years.

Learn more

Automotive Market Review and Outlook 2014 The Americas

This 75-page report features in-depth analysis of the automotive industry for the Americas. It includes discussions of market trends, legislative/regulatory activity impacting production and threats as well as design strategies being implemented by the major automakers. Detailed charts and data tables outline North American automotive production over the last five years.

Learn more

Plastics Building & Construction Market Review and Outlook 2014 with MS Excel chart data

This report provides in-depth analysis of the plastic building and construction market for North America, including discussions of trends, opportunities, threats and the latest developments in construction trends that impact plastics processors.

Learn more

Upcoming Plastics News Events

May 6, 2014 - May 8, 2014Plastics in Medical Devices 2014

May 12, 2014 - May 12, 2014Plastics News Brazil Pharma Summit

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

February 3, 2015 - February 7, 2015Plastics News Executive Forum 2015

More Events