Leaders say Europe's waste-recovery goal is achievable

Published: February 7, 2012 6:00 am ET

Related to this story

Topics Packaging, Sustainability, Public Policy, Materials, Recycling, Suppliers

BRUSSELS (Feb. 7, 1:15 p.m. ET) — The European plastics industry has set an ambitious target: total elimination of plastics waste going to landfills by 2020. PlasticsEurope, with the support of other representative bodies, declared the industry’s intent last year when it called for a Europewide landfill ban.

Wilfried Haensel, executive director of PlasticsEurope, said: “Eliminating landfill in all European countries is far from being an unrealistic goal. Frontrunner countries have reduced landfilling of plastics waste to almost zero, with significant environmental benefits.”

Europe’s combined rate of recycling and energy recovery from plastics waste in 2010 was 58 percent. There is a significant way to go to reach the target rate of 100 percent, and this prompts some questions: How will the goal be achieved? How do you overcome obstacles such as the widely different rates in European countries?

Ton Emans, recently elected as president of EuPR, the Brussels-based plastics recycling organisation, told European Plastics News: “This target is ambitious but can be achieved with appropriate changes in waste management.

“For instance, we should have harmonized policies across Europe and should generate well separated streams in order to have quality input for plastics recyclers. These important changes will permit the growth of Europe’s resource efficiency, create a substantial number of jobs and reduce CO2 emissions thanks to the reuse of recycled plastics.”

There has been a historical lag between the best and worst European countries for plastics recycling and recovery. There has been improvement in the past two years, and the rate increased from 54 percent in 2009 to 58 percent in 2010.

In packaging, figures for 2010 released by the European Association of Plastics Recycling and Recovery Organizations (EPRO) showed that 16 nations recycled more than 30 percent of its plastic packaging waste in 2010. But Bulgaria, Greece, Cyprus and Malta were still lagging with rates below 22 percent.

Harmonization and better enforcement of EU waste directives would close the gap. PlasticsEurope is calling upon policy-makers in all countries to support better waste structures that replicate the success of Germany, Denmark, Sweden and Austria, where significant landfill restrictions have been put in place.

As well as policy, there are obstacles in the recycling industry that need to be overcome. Jan-Erik Johansson, PlasticsEurope’s resource efficiency program director, says there are challenges in various areas. There should be a drive towards collecting all plastics for recycling and recovery. At the reprocessing stage, a focus on quality would help to target used plastics into the right applications. End use markets for recycled products also need to be developed.

Johansson said that in the tough economic and financial climate, support needs to be given by governments and institutions to stimulate further recycling and recovery.

“A common roadblock is access to financing for the infrastructure needed to capture the value in the plastics which is currently disposed in landfill - estimated to be 8 billion euros per year for the EU27 plus Norway and Switzerland,” he said.

There is clearly a lot of work to be done between now and 2020. Knowledge transfer is an important tool, and PlasticsEurope runs a project with the plastics industries in France, Poland, Spain and the UK with the objective of accelerating recovery improvement.

Reaching the 2020 target will be a tough job. But the success of the Vinyl 2010 program shows that cross-border efforts in plastics recycling can indeed achieve desirable results.


Comments

Leaders say Europe's waste-recovery goal is achievable

Published: February 7, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Residents ask court to close pipe maker

November 21, 2014 3:22 pm ET

Residents living by National Pipe & Plastics Inc.'s new factory in an industrial zone of Endicott, N.Y., say the facility has “devastated the...    More

Image

Small is beautiful in Nissei's newest press

November 21, 2014 2:14 pm ET

Responding to customer demand for flexibility, Japanese plastics-equipment manufacturer Nissei Plastic Industrial Co. Ltd. is demoing a caster-...    More

Image

Three advancements have driven injection molding technology

November 21, 2014 6:00 am ET

Injection molding technology has made major advances in the last 25 years, from largely a world of shoot-and-ship to doing as much as possible at the ...    More

Image

Renners leaving Sumitomo (SHI) Demag

November 21, 2014 10:01 am ET

Christian Renners is leaving injection molding press manufacturer Sumitomo (SHI) Demag Plastics Machinery GmbH, the company announced Nov. 21.    More

Image

Dow reaches agreement with Third Point

November 21, 2014 9:11 am ET

Dow Chemical Co. has reached an agreement with the investment firm that has been trying to force the company to sell off some assets.
More

Market Reports

Plastics in Brazil - State of the Industry Report

This in-depth report examines the Brazilian plastics industry from a historical and geographical context. Our analysts provide insight on economic trends and forecasts, growing manufacturing sectors that utilize plastics, private investment opportunities, market environment challenges, and innovations in R&D.

Data tables and charts on producer prices, trade, plastics production and end market indicators is also included.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molders Market Report & Ranking 2014

This special package contains our 132-page 2014 Market Report on the Injection Molding segment and our exclusive 2014 RANKINGS database of 500+ Injection Molders for a discounted package price.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

October 27, 2015 - October 29, 2015Plastics Financial Summit - New York - 2015

More Events