EPA issues new emissions rules for PVC production

By Rhoda Miel
News Editor

Published: February 16, 2012 6:00 am ET

Related to this story

Topics Sustainability, Public Policy, Materials, Suppliers

WASHINGTON (Feb. 16, 4:25 p.m. ET) — The U.S. Environmental Protection Agency has issued new emission standards for PVC production that it said will improve air quality and public health near production sites, but also cost an estimated $18 million in capital investment improvements at PVC production sites.

The 17 U.S. facilities that fall under the EPA’s Maximum Achievable Control Technology regulation will also spend a total of more than $4 million more per year to maintain operations under the new requirements.

The guidelines, issued on Feb. 13, update rules last revised in 2002. The agency hosted two public hearings and a series of studies before launching the changes.

In a fact sheet issued by EPA, the agency said the final rule sets emission limits and work practice standards for total organic air toxins and also for three specific air toxics: vinyl chloride, chlorinated di-benzo dioxins and furans as well as hydrogen chloride. Previously the rule set an emission limit for vinyl chloride only and used that level as a “surrogate” for all other air toxins.

The changes will reduce emissions from major sources by 238 tons of total air toxics, the agency said.

Facilities will have the flexibility to choose the “most practical and cost-effective control technology or technique to reduce the emissions,” the agency said in a Feb. 14 news release.

Ten of the operations affected by the rulings are in Texas and Louisiana with two more in New Jersey and one each in Delaware, Illinois, Kentucky, Michigan and Mississippi.

The Vinyl Institute, based in Alexandria, Va., said it is “cautiously optimistic” that the agency considered the full range of data available on PVC production before authorizing the final rules, but noted that EPA has added to the list of emissions the industry must monitor.

VI members spent 18 months and invested “millions of dollars” in benchmarking emissions from vinyl production to use as a basis in updating the MACT rules, the group said in a news release.

“PVC resin manufacturers in the United States have demonstrated their commitment to the environment over the past 20 years by reducing their emissions 80 percent or more even as PVC production increased 77 percent domestically,” said VI President Richard Doyle.

VI will conduct an extensive technical review of the final rule to understand it more fully.


Comments

EPA issues new emissions rules for PVC production

By Rhoda Miel
News Editor

Published: February 16, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Proposed Shell project draws more than 1,000 to informational meetings

April 17, 2014 2:03 pm ET

More than 1,000 people attended a pair of public meetings hosted by Shell Chemical LP on April 16 to discuss the possibility of building a major...    More

Image

Hedging can slow the resin rollercoaster

April 17, 2014 3:00 pm ET

The good old days — if they even ever existed — are gone, and.Andy VanPutte thinks volatility in the resin market is here to stay and...    More

Texas consumer group urges more science in advocacy campaigns

April 17, 2014 1:35 pm ET

WASHINGTON—The Texas Consumer Association (TCA) is raising concerns about consumer advocacy campaigns against certain chemicals and plastic...    More

Spain's Cristian Lay Group buys two materials units of bankrupt LSB

April 17, 2014 11:11 am ET

Spanish industrial conglomerate Cristian Lay Group has purchased two of the bankrupt Spanish PET packaging group La Seda de Barcelona.    More

Image

Using social media to answer consumer questions about plastics

April 17, 2014 10:59 am ET

Plastic packaging was stoutly defended on a recent Q&A session on social media site Twitter, run jointly by the British Plastics Federation and scienc...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report provides analysis and discussions of economic and political conditions, market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as strategies being implemented by thermoformed packaging companies. In addition, there are reviews of 25 leading thermoformers in the packaging segment, assessing their growth initiatives and performance metrics over 10 years.

Learn more

Automotive Market Review and Outlook 2014 The Americas

This 75-page report features in-depth analysis of the automotive industry for the Americas. It includes discussions of market trends, legislative/regulatory activity impacting production and threats as well as design strategies being implemented by the major automakers. Detailed charts and data tables outline North American automotive production over the last five years.

Learn more

Plastics Building & Construction Market Review and Outlook 2014 with MS Excel chart data

This report provides in-depth analysis of the plastic building and construction market for North America, including discussions of trends, opportunities, threats and the latest developments in construction trends that impact plastics processors.

Learn more

Upcoming Plastics News Events

May 6, 2014 - May 8, 2014Plastics in Medical Devices 2014

May 12, 2014 - May 12, 2014Plastics News Brazil Pharma Summit

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

February 3, 2015 - February 7, 2015Plastics News Executive Forum 2015

More Events