Expert: Firms should measure return-on-investment of lean manufacturing

By Bill Bregar
Senior Staff Reporter

Published: March 5, 2012 6:00 am ET

Related to this story

Topics Injection Molding Blow Molding Film & Sheet Pipe/Profile/Tubing Rotomolding Thermoforming
Companies & Associations

TAMPA, FLA. (March 5, 12:15 p.m. ET) — Lean manufacturing and Six Sigma programs are certainly popular, but manufacturers often don’t measure their bottom-line effectiveness — measured in dollars-and-cents payback, according to a speaker at the Plastics News Executive Forum.

“We ultimately believe that lean and Six Sigma should be treated like any capital investment,” said Andrew Csicsila, a Chicago-based director in the business consulting firm AlixPartners LP.

Csicsila presented results of the firm’s survey last year of 100 respondents. Eighty-five percent of them had some type of formal program.

A key finding: Most companies are getting a poor return on investment from lean and Six Sigma, and a surprising number of executives don’t even know the ROI or even have a specific target.

“One thing that we feel is the benefit of lean and Six Sigma is actually the return on investment in these programs,” he said. “Where’s the cash?”

Csicsila outlined several findings from the survey. Expectations were very low at more than half of the companies, where officials targeted savings of 5 percent or less per year from lean or Six Sigma—and most companies failed to meet even those low targets.

Only one fourth of the respondents realized a payback in a year or less. Surprisingly, Csicsila said, more than 40 percent were unsure of the ROI.

When it comes to Six Sigma and lean, Csicsila said the survey showed there is a “large perception gap and a lack of understanding of return on investment.” He reported a big disconnect, as officials reported widespread satisfaction with their efforts. At the same time, nearly 60 percent of people responding to the survey said that less half of any reported savings shows up on the bottom line and is sustained over time.

Csicsila gave suggestions on how to improve performance. Measuring the payback in cash—not the number of black belts—is the way to gauge the effectiveness of money spent, he said.


Comments

Expert: Firms should measure return-on-investment of lean manufacturing

By Bill Bregar
Senior Staff Reporter

Published: March 5, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Haitian builds system for Renault's new China auto assembly plant

April 24, 2015 11:10 am ET

A late-comer to the world's largest auto market, French carmaker Renault SA is currently building its first factory in China.    More

Image

Wittmann Battenfeld betting on big for future sales

April 24, 2015 12:34 pm ET

Five hundred visitors packed into MacroPower Days, about twice as many as Wittmann Battenfeld GmbH officials initially expected — proof, they...    More

Image

Michigan OSHA fines injection molder

April 23, 2015 4:09 pm ET

Michigan-based injection molder Grand Rapids Plastics Inc. faces $558,000 of fines following inspections from state regulators investigating the June ...    More

Image

Deluxe Plastics honored for cart designed to make tool changes easier

April 21, 2015 4:24 pm ET

Deluxe Plastics Inc. used its single-minute exchange of die — or what is better known as a SMED cart — to claim the first Innovation...    More

Image

Keeney adds nine presses to increase capacity at two plants

April 20, 2015 4:21 pm ET

Keeney Manufacturing Co. has installed nine more injection molding machines at two of its East Coast plants to increase production capacity for plasti...    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 15, 2015 - September 17, 2015Plastics Caps & Closures - September 2015

More Events