Polyethylene and polypropylene prices rise despite slow demand

By Frank Esposito
Senior Staff Reporter

Published: March 29, 2012 6:00 am ET

Related to this story

Topics Materials, Suppliers

AKRON, OHIO (March 29, 2 p.m. ET) — North American prices for polyethylene and polypropylene resins increased for the second straight month in March, with feedstock issues and supplier discipline overriding slow demand growth for both materials.

Regional prices for all grades of high low and linear low density PE are up an average of 3 cents per pound since March 1, according to buyers contacted by Plastics News. PP prices in the region are up an average of 5 cents per pound in that same span, buyers said.

The PE move is the second half of a 6-cent attempt originally announced for Jan. 1. The first 3 cents of that move took hold in February. The 6 cents in total increases seen so far in 2012 represents a hike of about 9 percent since Jan. 1, based on blow molding grades of HDPE for dairy applications.

Including a surprising 5-cent hike that hit the market in December, prices have jumped almost 15 percent in the last four months.

The March increase found a grip in the market even as regional PE demand was “steady to slow overall,” according to the PetroChem Wire consulting group in Houston. Maintenance turnarounds have limited supplies of ethylene feedstock at some locations, but market watchers said that PE makers’ desire to increase margins played a strong role as well.

One Texas-based PE buyer described March as “a no-flinch month” for PE makers, meaning that none of them offered to reduce or pull the 3-cent increase. The buyer added that the success of the March hike “wasn’t what I expected.”

Market analyst Mike Burns described PE makers’ behavior in March as “very disciplined,” which helped the increase go through in spite of relatively inexpensive feedstocks, a large inventory build and a big drop in export sales in the first two months of the year. Burns is with Resin Technology Inc. in Fort Worth, Texas.

And even though most PE made in North America uses natural gas-based ethane as a feedstock — instead of crude oil-based naphtha — prices in North America continue to follow oil prices. U.S. crude oil prices began the year around $99 per barrel and peaked above $109 in late February. Prices were near $105 in early trading March 29 — an increase of about 6 percent since the start of the year.

By comparison, U.S. natural gas prices began the year around $3 per million British thermal units (BTUs) but were at $2.25 in early trading March 29, for a price drop of 25 percent.

In PP, prices moved up 5 cents after absorbing a crushing 17-cent hike in February. Propylene feedstock makers had been seeking 15 in March, making the 5 cents seem like a victory of sorts for PP buyers. Propylene monomer also only took the 5 cents in March. Changes in monomer pricing have been directly passed through to the PP market in recent years.

PP prices in the region now are up an average of 23 percent since Feb. 1, based on injection molding and general purpose grades of homopolymer PP. March PP demand in the region was weak, according to PetroChem Wire, since buyers had bought ahead in anticipation of last month’s double-digit move.

PP supplies were affected in March by a force majeure situation at a plant operated by Pinnacle Polymers in Garyville, La. Production at the plant was reduced because of limited supplies of propylene feedstock. Propylene supplies in the region remained somewhat tight because of maintenance turnarounds.

Higher U.S. gasoline prices also may be causing propylene to be diverted into that market and away from PP, since the material can be used as a gasoline additive. Average U.S. gasoline prices began the year around $3.25 per gallon, but had rocketed to $3.90 in early trading March 29 — a 20 percent hike.

PE markets in the U.S. and Canada are working to recover from a 2011 year in which HDPE sales grew about 3 percent, but sales of LDPE and LLDPE were essentially flat. North American PP sales — including Mexico — are trying to rebound from a 4 percent sales drop in 2011.


Comments

Polyethylene and polypropylene prices rise despite slow demand

By Frank Esposito
Senior Staff Reporter

Published: March 29, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

A. Schulman reports growth in sales and profit

October 22, 2014 7:58 pm ET

Executives with materials maker A. Schulman Inc. have to be smiling after seeing full results for the firm's 2014 fiscal year.    More

Image

PolyOne takes on LED lighting

October 22, 2014 4:23 pm ET

PolyOne Corp. is making inroads into LED lighting applications with its Therma-Tech-brand material technology.    More

Image

Sales, orders climbing for Wittmann Battenfeld

October 22, 2014 4:04 pm ET

Equipment maker Wittmann Battenfeld GmbH expects sales this year to increase 7 percent, to 295 million euros, as it said some key markets, including...    More

Image

Bergen International adds manufacturing space, extrusion line

October 22, 2014 3:42 pm ET

Chemical foaming agent manufacturer Bergen International LLC recently doubled its manufacturing capacity, added an extrusion line and laboratory...    More

Image

DuPont materials taking more ground in auto, medical, electronics

October 22, 2014 2:41 pm ET

Materials made by DuPont Co. are making inroads with products ranging from auto coolant pipes to circuit breakers to surgical devices.    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events