Husky's goal: thinner parts, faster machines

By Bill Bregar
Senior Staff Reporter

Published: April 2, 2012 6:00 am ET

Related to this story

Topics Injection Molding, Machinery, Molds/Tooling

ORLANDO, FLA. (April 2, 8:30 p.m. ET) — Husky Injection Molding Systems Ltd. (Booth 3763) is not done pushing the envelope of thinner and faster, when it comes to packaging and medical molding.

A Husky official also said the company would break ground on a new plant in China.

At NPE2012, Husky is rolling out the latest generation of its HyCAP beverage closure maker, cranking out a water bottle closure at a 2.2 second cycle using a 96-cavity closure mold made by KWT Group, the Austrian closure mold specialist that Husky bought last year.

Jeff MacDonald, vice president of marketing, said Husky can squeeze out the cycle times because the company makes the molding press, hot runners and—now in closures—the mold.

The press running caps in Orlando represents a 45 percent improvement in productivity over the first HyCAP, at the last NPE in 2009, which ran a 72-cavity system running a similar application on a 2.4 second cycle. It’s a single-faced mold, not a stack mold. MacDonald said Husky said the market is moving away from stack molds for closures. “We’re finding the average cavitation’s coming down a little bit,” he said as Husky’s press conference April 2.

And Husky will go one step further at Chinplas, coming up April 18-24 in Shanghai, debuting the HyCAP HPP (for high performance package), which the company claims will be the world’s fastest closure system.

MacDonald said the press, which is already in China for the show, trims cycle time even more. The goal for Husky engineers was to reduce the mold open and close and make other improvements, to boost productivity and energy efficiency both by 20 percent, he said.

At NPE2012, Husky also is running an all-electric H-MED AE press with UltraSync hot runner technology, Shotscope NX to cut energy use and boost productivity, and an Altanium temperature controller. The H-MED is molding an IV breather cap.

MacDonald said Husky will break ground on a plant in the Shanghai area. He declined to give many details, but said it would do some manufacturing of hot runners and injection presses.

Husky opened its Asian headquarters plant in Shanghai in 2004, and followed up with a hot-runner plant in Shenzhen the following year.

Earlier this year, Husky opened a factory in Chennai, India, to do mold conversion and mold and hotrunner refurbishment for local preform makers.

MacDonald said Husky typically has expanded globally to supply major beverage bottlers.

In other news, MacDonald said Husky is coming out with its HyPEt HPP, after launching the HyPET AE at the 2010 K show in Germany. Husky has sold about 30 HyPET AE machines, he said.

He dubbed the news model the HyPET 4.0 – using Silicon Valley terminology, since Husky wants to introduce presses with major advancements about every two years. It will enable Husky to reduce PET preforms even more, by using a better mold and hot runner system and improving machinery performance.


Comments

Husky's goal: thinner parts, faster machines

By Bill Bregar
Senior Staff Reporter

Published: April 2, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Gear pump maker Witte expands in Germany and USA

July 25, 2014 2:15 pm ET

Witte Pumps & Technology GmbH, the German maker of gear pumps for extrusion, has moved into a new headquarters factory in the Hamburg area, and the...    More

Image

Austrian mold maker seeking North American manufacturing partner

July 25, 2014 1:49 pm ET

An Austrian mold maker is looking for a manufacturing location in North America.    More

Image

Tooling Technology has new private equity owner

July 25, 2014 11:55 am ET

New York private equity firm GenNx360 Capital Partners has partnered with management to buy Tooling Technology Holdings LLC, a diversified Ohio-based ...    More

Image

Columbine Plastics moving to new Colorado site

July 25, 2014 11:38 am ET

Custom injection molder Columbine Plastics Corp. plans to move from Boulder, Colo., to the Colorado Technical Center in Louisville, Colo.    More

Image

Metals and plastics company NN to buy Autocam in $300 million deal

July 25, 2014 10:07 am ET

A Tennessee metals and plastics company said it has agreed to acquire auto parts supplier Autocam Corp. in a deal valued at $300 million.    More

Market Reports

Plastics Recyclers Data Report & Directory

This exclusive MS Excel database contains all the companies from Plastics News' ranking of top North American Recyclers and Brokers by reprocessed volume and also includes a directory with materials processes, services offered and company contact information. Data is based on primary research by PN editorial staff.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events