More machines at NPE means more recycling - a lot more

Mike Verespej

Published: April 3, 2012 6:00 am ET

Related to this story

Topics Sustainability, Recycling, Machinery, NPE 2012

ORLANDO, FLA. (April 3, 8:45 p.m. ET) — Maine Plastics Inc. projects that it will recycle in excess of 350,000 pounds of plastics at NPE2012 in Orlando — or almost three times as much as the 125,000 pounds it recycled at NPE2009 in Chicago.

“We have 55 exhibitors running materials through their machines,” said Robert Render, CEO of Maine’s environmental and consulting business, A Greener Solution LCC, and vice president and past president of Zion, Ill.-based Maine Plastics.

The company has been the official recycler for five consecutive NPE shows.

The volume of plastic scrap being recycled is even more impressive, he said, when you take into account that three years ago NPE was a five-day show and 75 exhibitors were running material and participating in the program.

“The number of participating exhibitors in the program is lower, but they are running more machines and creating more scrap,” said Render, who believes that the exhibitors are “running full blast” with their machines because NPE is a four-day show instead of five.

The majority of the recycling activity, he said, is in the West Hall where Maine has its recycling operations set up in the docking area outside. At NPE2009, Maine recycled 95 percent of the potential recoverable materials. This year the target is to equal or surpass that same percentage.

Maine supplies exhibitors with two different size bags, two different containers or gaylords to use to collect the scrap or products they make at the show.

Render said most exhibitors use either the 75 two-wheeled 96-gallon blue bins supplied by Orlando, Fla.-based Rehrig Pacific Co., or the 20 MACX48 bins supplied by Decade Products, part of Grand Rapids, Mich.-based Cascade Engineering Inc.

Some companies supply their own bins, Render said. And unlike other years when gaylords were popular, he said only three gaylords are in use at NPE 2012 for recycling.

Moving the bins back-and-forth from the show floor to the loading docks is smoother at NPE2012 since exhibitors have “more flexibility” in how to move them from their booth to the dock than they did at previous NPEs, he said.

The majority of the plastics recycled are “the commodity resins—polypropylene, polyethylene, polystyrene and PET,” Render said.

To facilitate sorting at the dock, Maine, as it did at previous NPEs, created a sample part board of all the parts run by the participating exhibitors. It uses a coding system so that each truckload that leaves the dock is a singular resin.

Maine is using a local trucker, who further consolidates the material into trailer loads of single resins that are shipped to the Maine recycling plant in Apex, N.C.

“There is a lot of stuff going on, and this is a new venue,” Render said. “But all of us [Maine, the Orange County Convention Center and the Society of the Plastics Industry Inc., which puts on the triennial show] have been thoroughly prepared. We did extensive preparation ahead of time.”

In addition, to make sure the recycling works smoothly during the show, Render said the three groups meet every day to discuss “the issues that come up.”

The staff of the OCCC—which is hosting its first NPE—has been “very cooperative,” added Render. One example, they provided separate compactors in the dock area for cardboard and for plastics. At McCormick Place in Chicago, there was a single compactor.

“The culture of the venue has helped with the recycled process,” said Render. “We are recycling more stuff.”

OCCC is responsible for recycling other plastics materials such as the film from carpets that are laid down for the show, and beverage and water bottles and other plastics tossed into waste and recycling bins at the show. The material is taken to a materials recovery facility where it is sorted into separate streams for recycling.

 In 2011, the OCCC recycled 71 percent of the dry waste generated at all the shows at the convention center. “When we initially met with them to discuss our recycling at the show, they had data on every individual show,” Render said.

“The recycling at the show is going well and it will meet the objectives” of SPI, said Render.

“Bill Carteaux [the president and CEO of SPI] recognizes that there is a lot of potential criticism of plastics from litter and wanted to put an emphasis on recycling,” said Render. 

He speculates that the recycling ethic at the OCCC—along with lower projected costs for exhibitors and attendees— may have been one of the catalysts for the move of the show to Orlando.


Comments

More machines at NPE means more recycling - a lot more

Mike Verespej

Published: April 3, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Audacious vandal stuns Taipei Plas

September 29, 2014 4:59 pm ET

Melodrama erupted at the traditionally tranquil Taipei Plas trade show on Sept. 28 when a mysterious intruder flung red paint at the Baumüller...    More

Image

Shini pushes into western China

September 29, 2014 4:28 pm ET

Despite intellectual-property brigands, Taiwan's Shini Plastics Technologies Inc. is zestfully pursuing the enormous Chinese market for plastics...    More

Image

Recycling group releases shrink sleeve label guidelines

September 26, 2014 4:02 pm ET

A post-consumer plastics recycling trade group is out with a set of recommendations to help guide the packaging industry on the use of shrink sleeve...    More

Image

Global giant Foxconn to make, sell molding machines

September 26, 2014 2:48 pm ET

For years, Taiwan's Foxconn Technology Group has been the world's largest contract manufacturer for electronics, with more than 1 million employees...    More

Image

Chemical regulation policy update likely to remain in limbo

September 26, 2014 1:13 pm ET

Efforts to broker a deal on national chemical regulation policy appear to have fallen apart in the waning days of the 113th Congress, leaving plastics...    More

Market Reports

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our industry analysis highlights macro industry trends and micro trends faced by companies that do business in Mexico. The report also provides key industry statistics and forecasts to anticipate future industry expansion.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Injection Molders Market Report & Ranking 2014

This special package contains our 132-page 2014 Market Report on the Injection Molding segment and our exclusive 2014 RANKINGS database of 500+ Injection Molders for a discounted package price.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events