Australian states seek federal ban on plastic bags

By Kate Tilley
Correspondent

Published: July 26, 2012 6:00 am ET

Related to this story

Topics Public Policy, Sustainability, Packaging, Film & Sheet

SYDNEY, AUSTRALIA (July 26, 7 a.m. ET) — Although some Australian cities, local councils and three states and territories have banned single-use plastic bags, Sydney-based Planet Ark Environmental Foundation Ltd. says other states are waiting for Australia’s Federal Government to act.

Planet Ark recycling campaigns manager Janet Sparrow said many Australian councils have been working for years to help communities go "plastic bag-free" by banning single-use, non-compostable bags. However, many states are disinclined to introduce material-specific waste regulations without a federal framework.

"Some states are reluctant to take action on something they see as having national implications or that may be better managed and regulated at a federal level," Sparrow said.

Her comments follow a Western Australian city becoming Australia’s first local government area to legislate a plastic bag ban.

Fremantle, a coastal port city 12 miles south of Western Australia’s capital, Perth, has drafted a law to ban bags less than 60 microns thick.

A City of Fremantle spokesman told Plastics News the law likely will be enacted by the end of 2012.

Fremantle first adopted a strategy to promote plastic bag alternatives in 2004, and several retailers stopped using plastic bags. "This was a non-regulatory approach, so it was never going to reach 100 percent of businesses. The purpose of creating a local law is to complement this approach with regulation that bans the worst plastic bags," the spokesman said.

Several Australian towns, such as Tasmania’s Coles Bay and Mogo, in southern New South Wales, have gone plastic bag-free since 2003, but Sparrow said the City of Fremantle will be the first council to enforce the policy with a law.

The law draws on existing legislation already passed in the state of South Australia, and the Northern Territory (NT) and the Australian Capital Territory (ACT). Like those governments’ laws, Fremantle’s bans plastic bags below a specified thickness and sets a minimum cost for plastic shopping bags.

In May 2009, South Australia became Australia's first state to ban HDPE bags. It passed a law prohibiting retailers from selling or giving away carry bags less than 35 microns thick, although "barrier" film bags, used for holding fruit and vegetables, meat or other perishables, are still permitted.

The NT banned lightweight single-use plastic bags Sept. 1, 2011, in a move similar to South Australia’s. The legislation also gives NT residents a $A0.10 rebate incentive to recycle eligible plastic, aluminum and glass beverage containers.

The ACT was the third Australian state or territory to ban plastic bags. It took effect on Nov. 1, 2011. Shoppers must take their own reusable bags to retail outlets or buy them at checkouts. The ban does not apply to barrier bags or compostable bags.

Sparrow said there has been serious discussion in Tasmania and in Western Australia about the possibility of adopting state-wide bans.

In 2010, the island state of Tasmania's Greens Party introduced a motion to ban non-biodegradable HDPE bags; it was supported by both Tasmania’s other political parties, the Labor Party and the National Liberal Party. The government in May said it has set aside $A780,000 ($US812,000) to develop legislation over the next three years.

A bill banning plastic shopping bags was introduced into West Australia's parliament in Mar. 2012 by the Labor Party opposition environment minister Sally Talbot. It sought to ban all plastic bags, with penalties of up to $A20,000 ($US21,000) for supplying them. However, the WA Government rejected the bill.


Comments

Australian states seek federal ban on plastic bags

By Kate Tilley
Correspondent

Published: July 26, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Coveris makes another flexible packaging buy

August 22, 2014 9:34 am ET

Coveris Holdings is continuing its rapid acquisition pace, this time picking up flexible print specialist Learoyd Packaging (Holdings) Ltd. to boost...    More

Image

Composite bridge maker also leading the way in installation

August 22, 2014 1:21 pm ET

Lightweight, low maintenance and strong, fiber-reinforced polymer (FRP) bridge decks finally are crossing the line from specialty projects to wider...    More

Image

Recycled HDPE prices climbing

August 22, 2014 11:26 am ET

North American selling prices for recycled grades of high density polyethylene resin have increased in recent months because of tight supplies of the ...    More

Image

Promens closing 2 German blow molding plants

August 22, 2014 9:54 am ET

Promens hf, the Icelandic packaging group, is planning to restructure its packaging operations in Germany with the closure of two blow molding plants ...    More

Image

Investment firm specializes in emerging polymer firms in Ohio

August 21, 2014 3:20 pm ET

A plastics market veteran is working with an investment firm and a research foundation to help commercialize polymer technology in the Buckeye State.    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events