SPI releases machinery statistics

By Bill Bregar
Senior Staff Reporter

Published: August 10, 2012 6:00 am ET

Related to this story

Topics Injection Molding, Film & Sheet, Pipe/Profile/Tubing, Thermoforming, Machinery

WASHINGTON (Aug. 10, 1 p.m. ET) — The plastics machinery rebound is continuing this year, according to the Society of the Plastics Industry Inc.’s Committee on Equipment Statistics.

Also, Washington-based SPI is releasing statistics on thermoforming equipment for the first time, and more categories of extruders.

Injection molding

For injection molding machines, the largest sector, SPI’s year-end report said 2011 ended with 2,849 injection orders, an increase of 13 percent over the order level of 2010. Economist Bill Wood, who provides an analysis for the SPI statistics, predicts a 10 percent increase for full-year 2012, or about 3,100 new orders.

Wood also thinks injection press shipments will gain 10 percent in 2012 — finishing this year at more than 2,900 units and approach the 3,000-press barrier. The low point came in the recession-hit 2009, when shipments sank to just 1,285.

Extrusion

For extrusion, SPI now is releasing numbers on more categories of equipment than before. Instead of one single number for all extruders, the Committee on Equipment Statistics now reports on single-screw extruders, and twin-screw extruders, both co-rotating and counter-rotating.

This year, Wood is predicting a modest increase in twin-screw extruders of 3-5 percent and a flat-to-modest increase for single-screw extruders. Wood runs Mountaintop Economics and Research in Greenfield, Mass.

SPI’s 2011 numbers show an increase in unit orders of just 1 percent from 2010. The annual dollar value was down by 10 percent.

In the twin-screw segment, SPI reports 150 new extruders were ordered in 2011, an 11 percent decline from 2010. The dollar value was 12 percent higher, although that number weakened toward the end of 2011, according to the report.

SPI said demand for counter-rotating twin-screw extruders “exhibited significantly more strength” than co-rotating machines. Orders of counter-rotating extruders slipped by only one machine in 2011 from 2010 — from 57 machines to 56 — but brought in a dollar value 28 percent greater.

Orders for co-rotating machines declined by 16 percent, from 112 units to 94, but managed a 5 percent dollar-value increase.

Most manufacturers of extruders are expecting business to hold steady or improve, fueled by expansions, new technology and an emphasis on energy efficiency.

Blow molding

Turning to blow molding, SPI said 2011 new orders for blow molding machines reached 85 units, a 16 percent increase from 2010. The dollar value for new orders jumped 19 percent.

Wood thinks blow molding machines will experience moderate growth this year, to about 90-100 blow molding machines.

SPI reported that the total number of auxiliary equipment units booked was 13 percent higher in 2011 from the year before. Exports declined modestly. A significant change in the number of companies reporting the data means that SPI officials are not comparing the numbers to 2010.

A similar issue comes in the components sector, which examines screws and barrels. Changes in the number of reporting companies makes it impossible to do year-over-year analysis on data for screws or barrels.

For the full year, a total of 7,970 components were shipped by reporting companies in 2011, as business conditions gradually improved.

Thermoforming

In the new category of thermoforming machinery, SPI reported that new orders in 2011 declined by 28 percent in terms of units and 25 percent in dollar value, from 2010 levels. But the shipment picture was brighter: shipments increased to 164 units, up 7 units from 2010, and the shipment dollar amount increased by 4 percent, according to SPI.

“The long-term incentives for equipment investment remain intact,” Wood wrote.


Comments

SPI releases machinery statistics

By Bill Bregar
Senior Staff Reporter

Published: August 10, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Baxter investing $300 million to expand dialyzers production in Alabama

August 29, 2014 12:53 pm ET

Baxter International, Inc. is expanding its Opelika, Ala. manufacturing location to boost production of dialyzers, a key component of hemodialysis...    More

Image

Obituary: Jerry Williams, Prism Plastics co-owner

August 29, 2014 8:50 am ET

Williams founded Prism Plastics with Rod Bricker and Gerry Phillips, after the three left Huron Plastics Group in 1999.    More

Image

Haitian's standardization efforts paying off

August 29, 2014 9:53 am ET

Streamlined design efforts and robust export sales helped propel Ningbo, China-based injection molding machine manufacturer Haitian International...    More

Image

Tighter resin prices leading to price hike for PE film

August 29, 2014 11:13 am ET

One of North America's largest film makers is pushing through a polyethylene price increase due, in part, to the tight resin market.    More

Image

American Starlinger-Sahm begins work on new US headquarters

August 29, 2014 10:18 am ET

American Starlinger-Sahm Inc., which sells equipment for woven plastic bag production, PET recycling equipment, sheet extrusion and laminating lines a...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events