SPI releases machinery statistics

By Bill Bregar
Senior Staff Reporter

Published: August 10, 2012 6:00 am ET

Related to this story

Topics Injection Molding, Film & Sheet, Pipe/Profile/Tubing, Thermoforming, Machinery

WASHINGTON (Aug. 10, 1 p.m. ET) — The plastics machinery rebound is continuing this year, according to the Society of the Plastics Industry Inc.’s Committee on Equipment Statistics.

Also, Washington-based SPI is releasing statistics on thermoforming equipment for the first time, and more categories of extruders.

Injection molding

For injection molding machines, the largest sector, SPI’s year-end report said 2011 ended with 2,849 injection orders, an increase of 13 percent over the order level of 2010. Economist Bill Wood, who provides an analysis for the SPI statistics, predicts a 10 percent increase for full-year 2012, or about 3,100 new orders.

Wood also thinks injection press shipments will gain 10 percent in 2012 — finishing this year at more than 2,900 units and approach the 3,000-press barrier. The low point came in the recession-hit 2009, when shipments sank to just 1,285.

Extrusion

For extrusion, SPI now is releasing numbers on more categories of equipment than before. Instead of one single number for all extruders, the Committee on Equipment Statistics now reports on single-screw extruders, and twin-screw extruders, both co-rotating and counter-rotating.

This year, Wood is predicting a modest increase in twin-screw extruders of 3-5 percent and a flat-to-modest increase for single-screw extruders. Wood runs Mountaintop Economics and Research in Greenfield, Mass.

SPI’s 2011 numbers show an increase in unit orders of just 1 percent from 2010. The annual dollar value was down by 10 percent.

In the twin-screw segment, SPI reports 150 new extruders were ordered in 2011, an 11 percent decline from 2010. The dollar value was 12 percent higher, although that number weakened toward the end of 2011, according to the report.

SPI said demand for counter-rotating twin-screw extruders “exhibited significantly more strength” than co-rotating machines. Orders of counter-rotating extruders slipped by only one machine in 2011 from 2010 — from 57 machines to 56 — but brought in a dollar value 28 percent greater.

Orders for co-rotating machines declined by 16 percent, from 112 units to 94, but managed a 5 percent dollar-value increase.

Most manufacturers of extruders are expecting business to hold steady or improve, fueled by expansions, new technology and an emphasis on energy efficiency.

Blow molding

Turning to blow molding, SPI said 2011 new orders for blow molding machines reached 85 units, a 16 percent increase from 2010. The dollar value for new orders jumped 19 percent.

Wood thinks blow molding machines will experience moderate growth this year, to about 90-100 blow molding machines.

SPI reported that the total number of auxiliary equipment units booked was 13 percent higher in 2011 from the year before. Exports declined modestly. A significant change in the number of companies reporting the data means that SPI officials are not comparing the numbers to 2010.

A similar issue comes in the components sector, which examines screws and barrels. Changes in the number of reporting companies makes it impossible to do year-over-year analysis on data for screws or barrels.

For the full year, a total of 7,970 components were shipped by reporting companies in 2011, as business conditions gradually improved.

Thermoforming

In the new category of thermoforming machinery, SPI reported that new orders in 2011 declined by 28 percent in terms of units and 25 percent in dollar value, from 2010 levels. But the shipment picture was brighter: shipments increased to 164 units, up 7 units from 2010, and the shipment dollar amount increased by 4 percent, according to SPI.

“The long-term incentives for equipment investment remain intact,” Wood wrote.


Comments

SPI releases machinery statistics

By Bill Bregar
Senior Staff Reporter

Published: August 10, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Kydex, Allen Extruders joined under Sekisui SPI name

September 17, 2014 4:12 pm ET

Sekisui Chemical Co. Ltd. is combining plastic sheet makers Kydex LLC and Allen Extruders LLC under one roof as Sekisui SPI.    More

Badger buys competitor Joseph Homa

September 17, 2014 4:04 pm ET

Badger Plug Co. has extended its protective plugs customer base by acquiring and closing a rival, Joseph Homa Consultants Inc. of Montreal.    More

Image

Georg Fischer closing SC pipe plant

September 17, 2014 2:58 pm ET

Georg Fischer Central Plastics LLC (GFCP) closed its manufacturing operation for pipe components in Abbeville, S.C., on Sept. 15, putting 17...    More

Image

Cascade Engineering founder Keller to step down as CEO

September 16, 2014 8:33 pm ET

Cascade Engineering Inc. is undergoing a transition as President Mark Miller will also add the role of CEO, replacing founder Fred Keller, who has...    More

Image

SPE Thermoforming Division picks 3 scholarship winners

September 16, 2014 4:25 pm ET

Three college students have earned scholarships through the Society of Plastics Engineers' Thermoforming Division, division officials announced at the...    More

Market Reports

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Thermoformed Packaging 2014 Market Review & Outlook – North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events