Hong Kong opens materials center to help firms upgrade

By Steve Toloken
News Editor / International

Published: August 21, 2012 6:00 am ET

Related to this story

Topics Public Policy Materials Design
Companies & Associations

HONG KONG (Aug. 21, 1:50 p.m. ET) — Hong Kong’s plastics industry hopes that a new government and industry-funded center of polymer information will help local companies upgrade and better handle the challenging economic situation.

At an Aug. 15 ceremony to open the HK$2 million (US$257.8 million) Plastic Materials Resources Centre, industry officials said they hope it will make it easier for companies to move into more advanced materials and upgrade their products and profits.

“I think it will give a platform that all the factory managers or the R&D people can have a place where we can discuss, ‘OK, we have a new product, what kind of material we can use, and what are the molding conditions,’ ‘’ said Daniel Wong, chairman of the Hong Kong Plastics Industry Council and one of two industry coordinators for the project. ‘’It will provide a platform to exchange ideas. This is what we hope we can achieve.’’

The focal point of the center is an easily searchable materials database, partly in Chinese and with contacts for local suppliers. The database was developed by the Hong Kong Productivity Council.

Historically, Hong Kong’s plastics industry has focused on manufacturing electronics, toys and consumer products using commodity materials like polyolefins and PVC and the more widely-used engineering materials like ABS and polycarbonate, said Stanley Cheung, an industry executive and convener of the working group that organized the center.

But if Hong Kong companies can upgrade their processing techniques and become more familiar with advanced materials such as polysulfone, polyetheretherketone or liquid crystal polymers, they can move into more lucrative markets, said Cheung, the general manager of Shenzhen, China-based hot runner maker Micotec (Shenzhen) Ltd.

Most Hong Kong plastics firms have shifted their factories to mainland China over the last 30 years and relied for too long on low-cost labor as a competitive advantage, said Cheung.

‘’When they moved to China they enjoyed the life of low labor costs, so this is why people did not emphasize technology,’’ said Cheung. ‘’But as you know the cost in China is no longer cheap.’’

Labor costs in Chinese factories have been rising about 15 percent for the last few years, and are likely to continue at that same pace for the next several years, industry officials said.

One Hong Kong business group estimated last month that 2,000 Hong Kong-owned factories in South China could close by the end of the year because of rising wages and weak export markets.

The focal point of the new center’s efforts to fight that is its materials database, which is available for public use at the facility, in the headquarters of Hong Kong’s Vocational Training Council in the Kowloon Bay neighborhood.

In addition to technical information on material properties and molding conditions, the database also has information on whether there are local suppliers of the resin, Cheung said.

The database is designed to be easy to search, for example by material type, trade name or manufacturer, he said. The center also contains sample displays of Hong Kong companies and other reference materials.

Locky Chu, the chairman of the VTC’s Plastics Training Board and director of mold maker Henmy Industries Inc., said the center will also help educate younger workers and give resources to universities and technical schools.

If organizers get positive feedback, they will look to expand the center, possibly by putting its database online or creating networked access, said Cheung, who is also vice chairman of the VTC’s Plastics Training Board.

One plastics executive attending the opening said efforts like the center are needed because Hong Kong is at risk of losing some technical skills.

Bernard Ting, chairman of the Hong Kong Toys Council and a senior executive at plastic molder Qualidux Industries Co. Ltd., said that’s partly because young people don’t see manufacturing as a ‘’glamorous’’ career.

‘’Hong Kong has suffered a shrinkage of technical skills,’’ said Ting. ‘’All over the world people will recognize we need industry in certain cities to sustain employment.’’

A little more than half of the budget for the center came from the Hong Kong government’s Small and Medium Enterprise Development Fund.

Other contributions came from the VTC and from industry, including a total of HK $100,000 (US $12,900) from three local firms – Micotec, Microban International (Asia) Ltd. and United Overseas Enterprises Ltd. – and the Hong Kong Mould and Die Council.

The project also had support from the Federation of Hong Kong Industries.


Comments

Hong Kong opens materials center to help firms upgrade

By Steve Toloken
News Editor / International

Published: August 21, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

California may require more recycled content in bottles

April 24, 2015 11:16 am ET

California lawmakers are considering a pair of bills that would bump up the required recycled content in plastic bottles for beverage companies to...    More

Image

Study suggests infants at lower risk from BPA exposure than expected

April 23, 2015 4:58 pm ET

A new study shows that newborn babies may have less risk from bisphenol A exposure than originally thought.    More

Image

Michigan OSHA fines injection molder

April 23, 2015 4:09 pm ET

Michigan-based injection molder Grand Rapids Plastics Inc. faces $558,000 of fines following inspections from state regulators investigating the June ...    More

Image

Clopay Plastics suing Berry over breathable film trade secrets

April 23, 2015 2:08 pm ET

Clopay Plastics Products Co. is alleging Berry Plastics Group Inc. stole trade secrets involving its breathable film technology used for baby and...    More

Image

Jeco adds Ferry rotational molder to handle increase in business

April 23, 2015 12:27 pm ET

Jeco Plastics Products LLC is ramping up for more work, adding a new Ferry 2600 rotational molder that will provide more capabilities.    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Woodís economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 15, 2015 - September 17, 2015Plastics Caps & Closures - September 2015

More Events