Report offers alternatives to extended producer responsibility

Published: September 14, 2012 6:00 am ET

Related to this story

Topics Packaging, Sustainability

PITTSBURGH (Sept. 14, 1:25 p.m. ET) — A cost analysis done for the Grocery Manufacturers Association argues that alternatives to extended producer responsibility policies can achieve high municipal solid waste recycling rates at reasonable costs and address a wider spectrum of the waste stream.

The report, released at the Sustainable Forum in Pittsburgh on Sept. 12, also claims that mandatory EPR programs aimed at food, beverage and consumer product packaging would not deliver on their promise of creating more cost-effective residential recycling programs and driving packaging redesign.

The report analyzed recycling rates, system costs, packaging changes, and other data from various European and Canadian jurisdictions that employ EPR for packaging. In the U.S., it looked at nationwide recycling rates and recycling programs in Ramsey County, Minn.

Among the study’s principal findings:

• Packaging use has declined in the United States, where there is no packaging EPR, but it has increased slowly in Europe, where there is widespread packaging EPR.

“There is no indication that EPR has reduced packaging use economy-wide or had any effect on package design or selection,” said the 68-page report, prepared for GMA by SAIC Energy, Environment & Infrastructure, LLC.

• Price signals sent by EPR to manufacturers are very weak in most jurisdictions compared to the overall value of the products they contain and price of packaging.

“Packaging EPR generally does not change the relative package cost among different package alternatives for a product,” said the report. “There is insufficient EPR fee differentiation to cause consumer packaged goods companies to switch from one package format to another.

The study also said that the U.S. has a higher recycling rate for municipal solid waste than both the European Union, 23 percent, and Canada, 18 percent, where EPR is widely employed.

It also noted that Ramsey County, a non-EPR jurisdiction in the Minneapolis-St. Paul area, has a lower net cost per ton ($156) than EPR programs in the Canadian provinces of Manitoba and Ontario, where costs are $166/ton and $202/ton, respectively. However, the report did not look at costs in any other specific municipalities in the U.S.

The report further argued that “states and municipalities already have at their disposal a suite of non-EPR policies that are both effective and efficient in terms of raising recycling rates.”

Specifically, the report cited more than a dozen approaches including disposal limits, recycling rewards or rebates for consumers, penalties, pay-as-you-throw disposal pricing, disposal bans, mandatory recycling of certain materials, diversion goals, landfill surcharges or taxes, advanced recycling/disposal fees, mandatory retail take-back programs, and building design standards.

“Together, [these initiatives] can achieve high recycling rates, without excess cost or administrative burden that results from EPR,” the report said.

“The most successful recycling and waste recovery programs will result from comprehensive approaches that leverage industry innovation and collaborative partnerships between NGO’s, government and industry, not one-size-fits-all mandates,” asserted Meghan Stasz, senior director of sustainability at GMA.


Comments

Report offers alternatives to extended producer responsibility

Published: September 14, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Composite bridge maker also leading the way in installation

August 22, 2014 1:21 pm ET

Lightweight, low maintenance and strong, fiber-reinforced polymer (FRP) bridge decks finally are crossing the line from specialty projects to wider...    More

Image

Recycled HDPE prices climbing

August 22, 2014 11:26 am ET

North American selling prices for recycled grades of high density polyethylene resin have increased in recent months because of tight supplies of the ...    More

Image

Promens closing 2 German blow molding plants

August 22, 2014 9:54 am ET

Promens hf, the Icelandic packaging group, is planning to restructure its packaging operations in Germany with the closure of two blow molding plants ...    More

Image

Non-recyclable items gumming up the works at recycling centers

August 21, 2014 3:46 pm ET

The influx of all sorts of unacceptable items at recycling centers has gotten to the point that Charlotte, N.C.-based ReCommunity is trying to bring...    More

Image

Bayer, SCAC partner on water reuse project

August 21, 2014 12:48 pm ET

Bayer MaterialScience (BMS) and Shanghai Chlor-Alkali Chemical Co. Ltd. (SCAC) have entered into a preliminary agreement for the reuse of waste water ...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events