OSHA fines Formosa Plastics — again

By Frank Esposito
Senior Staff Reporter

Published: September 20, 2012 6:00 am ET

Related to this story

Topics Public Policy, Materials, Suppliers

DELAWARE CITY, DEL. (Sept. 20, 2:30 p.m. ET) — For the second time in three years, Formosa Plastics Corp. USA has been fined for alleged safety and health hazards at its dispersion PVC resin plant in Delaware City.

On Sept. 19, the Occupational Safety and Health Administration announced $148,700 in proposed penalties for 16 alleged violations at the site, which employs about 100. Two of the violations are repeat offenses that also were cited in a separate investigation in early 2010.

Those repeat violations involve alleged failure to perform process equipment inspections and tests, failure to inspect critical valves and failure to ensure that PVC dust did not accumulate on surfaces and on the floor of a bagging area.

The other violations include alleged electrical hazards, lack of machine guarding, incomplete emergency shutdown procedures and other claims, all of which are classified as serious violations by OSHA.

“This employer continues to disregard OSHA’s process safety management standard and put its workers at risk of injury and possible death,” Domenick Salvatore, office director for the Wilmington, Del., area, said in a news release.

Officials with Livingston, N.J.-based Formosa “are currently reviewing” the OSHA report, spokesman Steve Rice said by phone Sept. 20. The firm has until Sept. 28 to respond to the citations.

The 2010 OSHA investigation produced 27 alleged serious violations — including a claim of unguarded floor holes and walkways — and a fine of $133,500. That investigation was begun after OSHA received a complaint from an employee at the site.

In late 2009, Formosa paid a civil penalty of almost $3 million to resolve several alleged environmental violations at its plastics and chemicals plants in Point Comfort, Texas, and Baton Rouge, La. At that time, the firm also agreed to spend more than $10 million on pollution controls at those sites.


Comments

OSHA fines Formosa Plastics — again

By Frank Esposito
Senior Staff Reporter

Published: September 20, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Blow molding machinery maker opens first plant in Taiwan

October 1, 2014 1:27 pm ET

Taiwanese equipment maker Kin Precision Industry Co. Ltd. has opened a 2,000-square-meter, 25-employee factory in Taichung, Taiwan, with an eye to...    More

Image

Global Plastics Summit puts PE prices in the spotlight

October 1, 2014 3:17 pm ET

Product manufacturers may start to shift away from polyethylene because of high prices, according to two major plastics processors.    More

Image

Speaker: Many issues can affect multi-cavity molds

October 1, 2014 2:02 pm ET

There are several conditions necessary across all cavities of a multi-cavity mold to ensure that all parts are produced the same. These include...    More

Image

Nucleation offers solution to shrinkage in HDPE closures

October 1, 2014 1:57 pm ET

For caps producers, nucleation can provide a practical solution to eliminate shrinkage variations in high density polyethylene beverage closures....    More

Image

Dow loses appeal in price fixing case

October 1, 2014 11:10 am ET

The Reuters press agency reports that a federal appeals court in Denver has rejected Dow Chemical Co.'s attempt to overturn a $1.06 billion fine impos...    More

Market Reports

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our industry analysis highlights macro industry trends and micro trends faced by companies that do business in Mexico. The report also provides key industry statistics and forecasts to anticipate future industry expansion.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Injection Molders Market Report & Ranking 2014

This special package contains our 132-page 2014 Market Report on the Injection Molding segment and our exclusive 2014 RANKINGS database of 500+ Injection Molders for a discounted package price.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events