Trexel expands relationship with Engel

By Bill Bregar
Senior Staff Reporter

Published: September 20, 2012 6:00 am ET

Related to this story

Topics Machinery, Molds/Tooling

WILMINGTON, MASS. (Sept. 20, 8:35 a.m. ET) — Trexel Inc. is growing globally by opening a new subsidiary in China and has expanded its working relationship with Austria-based injection press maker Engel Holding GmbH.

Trexel’s MuCell technology adds tiny bubbles to the melted plastic by bringing nitrogen gas to a supercritical state. When the melt comes out of the barrel, the bubbles are released inside the mold.

The low-pressure process cuts cycle times and allows parts to be molded in smaller-tonnage machines. Other benefits included reduced part weight, material savings, less warpage and better dimensional stability, according to Trexel.

President and CEO Steve Braig said the company in Wilmington, Mass., has quadrupled its engineering staff over the past several years. “Today we can do applications that were impossible three or four years ago,” he said.

One example: large MuCell instrument panel parts for Ford Motor Co. That won a top award at the Society of Plastics Engineers 2011 Automotive Innovation Awards.

Braig said MuCell offers automakers a way to reduce weight, as they try to meet federal highway standards of 54.5 mpg for cars and light trucks by 2025. “It’s a technology that can be implemented today,” he said in a Sept. 17 phone interview.

Trexel is enjoying good sales, Braig said. He declined to give a dollar amount, but said: “We finished our fiscal year at the end of June, and our revenues are up 48 percent. So we’re pretty excited about that versus the year prior.”

In China, Trexel is expanding its customer base to include domestic processors. Trexel has been supporting China from Hong Kong, and conducted the transactions from the U.S. headquarters. That was fine when Trexel was dealing with multinational companies with operations in China, but now Trexel also is targeting domestic Chinese-owned companies, he said.

Trexel runs two mid-sized injection molding presses at an office in Shenzhen. In late August, the company announced plans for a technical center in Shanghai that will have larger press capacity.

“We are looking for a location to have large-tonnage machines, so we can do molding trails,” Braig said.

Roger Cheng, the technical manager of Trexel’s Hong Kong office, has become general manager of Trexel (Shenzhen) Technology Co. Ltd. The Hong Kong unit will support Australia and Southeast Asia.

Trexel has hired an automotive account manager, who is building a team to focus on that industry.

“We’re still hiring staff (in China), so we’re still ramping up,” Braig said. “This is not to manufacture. This is to support the local markets with processing knowhow and ultimately with equipment and spare parts.”

Automotive is a major market for Trexel. But other manufacturing sectors in China also are adopting MuCell. Braig said Trexel sold 10 systems for a manufacturer of industrial cleaning equipment in China, which molds the large spinning disc that the polishing brush attaches to, for a floor buffer. The park has to be perfectly round. MuCell helps another customer, a Japanese company’s printer manufactured in China, mold precision housing parts for a laser printer.

Braig said Trexel is working in China with some global packaging suppliers to use MuCell to reduce costs of food containers and closures.

Trexel offers a more-basic, lower-cost version of MuCell for the region.

“It’s an education process. We’re participating in a lot of conferences there, and we also have developed a partnership with Haitian and Borch,” Braig said, referring to Chinese injection press makers Haitian International Holdings Ltd. and Guangzhou Borch Machinery Co. Ltd. Those agreements cover China and Southeast Asia.

In other news, Engel is now fully integrating MuCell units into its Victory and e-Victory molding machines. That means the MuCell control is tied into the machine controller, reducing cost and making it easier to setup the press.

The Engel presses are tie-barless, so you can use larger platens, allowing relatively small machines to accommodate large molds—and take full advantage of the MuCell process that requires less clamping force tonnage, the two companies said.

Engel said that, in many MuCell applications, a 500-ton Victory press can replace a larger, 700-ton Engel Duo press, for a significant cost savings.


Comments

Trexel expands relationship with Engel

By Bill Bregar
Senior Staff Reporter

Published: September 20, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Sales, orders climbing for Wittmann Battenfeld

October 22, 2014 4:04 pm ET

Equipment maker Wittmann Battenfeld GmbH expects sales this year to increase 7 percent, to 295 million euros, as it said some key markets, including...    More

Image

Asia continues driving sales for Engel

October 21, 2014 2:42 pm ET

The number seven seems to be special for European plastics machinery makers at the moment — injection press giant Engel Holding GmbH said Oct....    More

Image

Trexel charges patent infringement against Taiwan company

October 20, 2014 3:25 pm ET

Trexel Inc., the supplier of the MuCell microcellular foaming technology, is accusing a Taiwanese company, Chuan Lih Fa Machinery Works, of violating ...    More

Image

Humanoid robot provides inspection service with a smile

October 17, 2014 6:00 am ET

Everyone knows robots can improve production and quality. But no one says they can't show a little personality while they're working.    More

Image

Hasco gets into augmented reality

October 17, 2014 6:00 am ET

Mold makers may be used to seeing cores and pins on the exhibition stand of a supplier — but not augmented reality that looks like it comes from...    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events