Too much 3D hype, says 3D printing consultant

James Snodgrass

Published: September 28, 2012 6:00 am ET

Related to this story

Topics Design

BIRMINGHAM, ENGLAND (Sept. 28, 1:30 p.m. ET) — The future for 3D printing is “not so rosy” said Todd Grimm, president of T. A. Grimm and Associates, an Edgewood, Ky., prototyping consultant, in an iconoclastic opening keynote during this week’s TCT conference in Birmingham.

Grimm urged the industry to adopt a more pragmatic approach.

In his provocative address, Grimm planted “seeds of doubt” about additive manufacturing based upon the gulf between what is practical today and what is promised in the future.

Citing Gartner Research’s 2012 Hype Cycle for Emerging Technologies special report — which indicates that 3D printing is reaching the “peak of inflated expectations” — Grimm blames media hype for distorting the reality of what can be done today and what we can reasonably expect in the short term future.

Examples of media hype that Grimm identified included Airbus’s announcement at Farnborough that it was going to 3D-print aircraft.

“What the media failed to tell you is that Airbus’s statement said ‘by the year 2050’ … not a single component on an Airbus aircraft flying today is made with additive manufacturing.

He also cited the stop-motion animated film ParaNorman, which used 3D printed facial expressions.

“What they failed to tell you,” said Grimm, “is that the producers did not save a single dollar or a single second”. What is important, he stressed, is that the producers had a new creative process to work with.

Grimm believes the hype has been fueled by the introduction of consumer-level 3D printers.

“At any time soon, the 3D printer will not become a staple in the household,” Grimm predicted. He lambasted the low-cost machines because their manufacturers have not invested in their development and in user interfaces, relying instead on open source code.

“Anyone could make one. What they are not doing is putting in the stability, the usability, the things that will actually make them work,” said Grimm.

But he suggested that the nascent consumer market will have an effect on the lower end of the professional market. He estimated that the two markets, consumer and professional, will converge at the $5,000 point.

“Additive manufacturing and 3D printing are a poor substitute for conventional manufacturing,” said Grimm, suggesting that the industry needs to look for the niches where it can offer a unique solution.

“The opportunity lies when you change the game. Stop looking at it as a direct substitute for injection molding or die casting.”


Comments

Too much 3D hype, says 3D printing consultant

James Snodgrass

Published: September 28, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Prosthetic arm concept wins in student thermoforming competition

August 22, 2014 1:56 pm ET

Pressure forming company Freetech Plastics Inc. has returned with its annual Student Thermoformed Part Competition, intended to expand the exposure...    More

Image

Ford demonstrates Magna's seamless rear window on new F-150

August 14, 2014 11:34 am ET

DETROIT — Ford Motor Co. today demonstrated its “seamless sliding rear window” feature developed by Canadian supplier Magna...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events