Igloo adds workers, 130 items, brings rotomolding in-house

By Rhoda Miel
News Editor

Published: October 2, 2012 6:00 am ET

Igloo's guard shack at the firm's headquarters has a familiar look. (Igloo Products Corp. photo)

Related to this story

Topics Consumer Products, Blow Molding, Injection Molding, Rotomolding

KATY, TEXAS (Oct. 2, 11:55 a.m. ET) — Four years after a change in ownership, Igloo Products Corp. has boosted sales nearly 50 percent, revived its product line with 130 new items and is in the midst of a manufacturing investment that has improved productivity.

The company — best known for its line of coolers — is also adding rotational molding to its in-house capabilities this year with five new manufacturing lines and 20 more employees in Katy, where it is based. Igloo currently has 85 percent of its products made in the U.S.

“Obviously, made in America is the right vibe to connect with a lot of consumers right now, but what we’ve also been able to prove is that if you have an efficient manufacturing base, you can not only build in America, you can build a product at a lower cost,” said Gary Kiedaisch, CEO and chairman, in a Sept. 17 telephone interview.

Igloo was already a familiar consumer name when private equity group JH Whitney & Co. of New Canaan, Conn., bought the firm in 2008 from Westar Capital of Costa Mesa, Calif.

The company estimates that 90 percent of U.S. homes have some kind of a cooler, and Igloo products make up 75-80 percent of them.

However, prior to the buyout, the company’s sales were flat, according to Kiedaisch. The new owners set out to change that through an emphasis on new and improved products.

While the privately owned company does not release specific sales data, official said sales were up by nearly 50 percent at the start of 2012. In 2011, workers in Katy made 19 million hard-sided coolers alone.

As those new products caught on, Kiedaisch said, Igloo needed more — and more-efficient — capacity in-house.

Executive Vice President David Thornhill has helped lead the improvements at Katy, with more-efficient equipment, better production layouts and vertical manufacturing. The company estimates its efficiency has climbed by 30 percent since 2008.

Igloo already had its own injection molding, blow molding and foam molding operations. Even more processes could come on line with the right business case, Thornhill said.

Igloo also has non-plastics operations such as cut-and-sew for soft-sided coolers and additional outdoor recreation items including chairs and tents.

Those investments in products and manufacturing came at the same time that costs were increasing outside the United States, which helped highlight the benefits of vertical manufacturing in-house

“When you look at our manufacturing strategy, it’s to bring as many processes as possible inside,” Kiedaisch said. “For us, the picture has been that near-shoring is much more favorable than it was even 18 months ago.”

Thornhill and Kiedaisch look to one of Igloo’s new products as an example of how its business outlook has developed since 2008 and is continuing to impact the company’s strategy.

Igloo introduced the Yukon Cold Locker cooler at the start of 2012. The high-end cooler is marketed at sports enthusiasts and professionals who will spend days — if not weeks — out in the woods or on a fishing expedition.

“These are the guys who will spend thousands of dollars on a gun or a thousand dollars on a scope,” Thornhill said.

The Yukon was designed with extra insulation, capable of retaining ice for up to 14 days, compared to seven for a typical cooler. That is the kind of performance needed to keep swordfish or elk fresh during a long fishing or hunting trip.

The hard plastic outer shell and heavy-duty latches and handles also stand up to rough usage. Thornhill boasts that in tests, a bear spent an hour trying to break in before it gave up.

The Yukon also sells at a premium price, retailing at more than $300 for a 50-quart container and more than $700 for the 250-quart model. By comparison, Igloo’s 50-quart MaxCold hard-sided cooler lists for $65.99

Yukon coolers are rotational molded, so when orders for the Yukon took off and tripled the expected production capacity, Igloo knew it was time to bring rotational molding in-house. It currently contracts for rotomolding from outside suppliers that use a combination of domestic and international production.

Igloo has cleared 15,000 square feet of space in Katy for rotomolding and Thornhill is looking at additional production that could use the process. There is also space for future growth, while adding rotational molding is now allowing the company to list the Yukon as “Made in America.”

“We’re tooling up for this in a big way,” Thornhill said. “We’re looking forward to getting that group up and running.”


Comments

Igloo adds workers, 130 items, brings rotomolding in-house

By Rhoda Miel
News Editor

Published: October 2, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

One51 adding injection molder Straight to its bin molding portfolio

July 29, 2014 10:12 am ET

Dublin-based One51 plc has had its purchase of British trash bin maker Straight plc cleared by the United Kingdom's Competition and Markets Authority.    More

Image

Columbine Plastics moving to new Colorado site

July 25, 2014 11:38 am ET

Custom injection molder Columbine Plastics Corp. plans to move from Boulder, Colo., to the Colorado Technical Center in Louisville, Colo.    More

Image

Metals and plastics company NN to buy Autocam in $300 million deal

July 25, 2014 10:07 am ET

A Tennessee metals and plastics company said it has agreed to acquire auto parts supplier Autocam Corp. in a deal valued at $300 million.    More

Image

Chinese auto suppliers growing in US

July 24, 2014 4:17 pm ET

Two China-based automotive suppliers are expanding in the U.S., according to information released by the Michigan Economic Development Corp.    More

Image

Rail improvements also allow rotomolder to improve operations

July 24, 2014 3:10 pm ET

An infrastructure improvement grant from the U.S. Commerce Department is helping an Indiana plastics plant expand its product line and add jobs.    More

Market Reports

Plastics Recyclers Data Report & Directory

This exclusive MS Excel database contains all the companies from Plastics News' ranking of top North American Recyclers and Brokers by reprocessed volume and also includes a directory with materials processes, services offered and company contact information. Data is based on primary research by PN editorial staff.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events