Igloo adds workers, 130 items, brings rotomolding in-house

By Rhoda Miel
News Editor

Published: October 2, 2012 6:00 am ET

Igloo's guard shack at the firm's headquarters has a familiar look. (Igloo Products Corp. photo)

Related to this story

Topics Consumer Products, Injection Molding, Blow Molding, Rotomolding

KATY, TEXAS (Oct. 2, 11:55 a.m. ET) — Four years after a change in ownership, Igloo Products Corp. has boosted sales nearly 50 percent, revived its product line with 130 new items and is in the midst of a manufacturing investment that has improved productivity.

The company — best known for its line of coolers — is also adding rotational molding to its in-house capabilities this year with five new manufacturing lines and 20 more employees in Katy, where it is based. Igloo currently has 85 percent of its products made in the U.S.

“Obviously, made in America is the right vibe to connect with a lot of consumers right now, but what we’ve also been able to prove is that if you have an efficient manufacturing base, you can not only build in America, you can build a product at a lower cost,” said Gary Kiedaisch, CEO and chairman, in a Sept. 17 telephone interview.

Igloo was already a familiar consumer name when private equity group JH Whitney & Co. of New Canaan, Conn., bought the firm in 2008 from Westar Capital of Costa Mesa, Calif.

The company estimates that 90 percent of U.S. homes have some kind of a cooler, and Igloo products make up 75-80 percent of them.

However, prior to the buyout, the company’s sales were flat, according to Kiedaisch. The new owners set out to change that through an emphasis on new and improved products.

While the privately owned company does not release specific sales data, official said sales were up by nearly 50 percent at the start of 2012. In 2011, workers in Katy made 19 million hard-sided coolers alone.

As those new products caught on, Kiedaisch said, Igloo needed more — and more-efficient — capacity in-house.

Executive Vice President David Thornhill has helped lead the improvements at Katy, with more-efficient equipment, better production layouts and vertical manufacturing. The company estimates its efficiency has climbed by 30 percent since 2008.

Igloo already had its own injection molding, blow molding and foam molding operations. Even more processes could come on line with the right business case, Thornhill said.

Igloo also has non-plastics operations such as cut-and-sew for soft-sided coolers and additional outdoor recreation items including chairs and tents.

Those investments in products and manufacturing came at the same time that costs were increasing outside the United States, which helped highlight the benefits of vertical manufacturing in-house

“When you look at our manufacturing strategy, it’s to bring as many processes as possible inside,” Kiedaisch said. “For us, the picture has been that near-shoring is much more favorable than it was even 18 months ago.”

Thornhill and Kiedaisch look to one of Igloo’s new products as an example of how its business outlook has developed since 2008 and is continuing to impact the company’s strategy.

Igloo introduced the Yukon Cold Locker cooler at the start of 2012. The high-end cooler is marketed at sports enthusiasts and professionals who will spend days — if not weeks — out in the woods or on a fishing expedition.

“These are the guys who will spend thousands of dollars on a gun or a thousand dollars on a scope,” Thornhill said.

The Yukon was designed with extra insulation, capable of retaining ice for up to 14 days, compared to seven for a typical cooler. That is the kind of performance needed to keep swordfish or elk fresh during a long fishing or hunting trip.

The hard plastic outer shell and heavy-duty latches and handles also stand up to rough usage. Thornhill boasts that in tests, a bear spent an hour trying to break in before it gave up.

The Yukon also sells at a premium price, retailing at more than $300 for a 50-quart container and more than $700 for the 250-quart model. By comparison, Igloo’s 50-quart MaxCold hard-sided cooler lists for $65.99

Yukon coolers are rotational molded, so when orders for the Yukon took off and tripled the expected production capacity, Igloo knew it was time to bring rotational molding in-house. It currently contracts for rotomolding from outside suppliers that use a combination of domestic and international production.

Igloo has cleared 15,000 square feet of space in Katy for rotomolding and Thornhill is looking at additional production that could use the process. There is also space for future growth, while adding rotational molding is now allowing the company to list the Yukon as “Made in America.”

“We’re tooling up for this in a big way,” Thornhill said. “We’re looking forward to getting that group up and running.”


Comments

Igloo adds workers, 130 items, brings rotomolding in-house

By Rhoda Miel
News Editor

Published: October 2, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Comar merging with Convergence Packaging

October 21, 2014 5:07 pm ET

A couple of plastic packaging companies owned by private investment firm Graham Partners are merging into a single entity.    More

Image

BASF targets coffee and automotive connoisseurs with new resin grades

October 21, 2014 2:07 pm ET

BASF SE is using polybutylene terephthalate (PBT), which is normally used to manufacture high-end electronics, in a food consumer packaging product.    More

Image

Report: Suspected former Nazi with plastic connection collecting Social Security

October 20, 2014 3:52 pm ET

AKRON, OHIO — A one-time plastics executive in Akron is among dozens of suspected former Nazis who have been collecting U.S. Social Security...    More

Molder expands in France with new clean room

October 20, 2014 1:30 pm ET

Global Closure Systems (GCS), a global injection molding producer, showed off its new ISO 7 clean room at its Astra Plastique factory in France...    More

Molder goes to auction block

October 17, 2014 12:17 pm ET

An Illinois custom injection molding operation will be auctioned off after its owner decided to close the business.    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events