Engel shows molding for electronic parts

David Eldridge

Published: October 4, 2012 6:00 am ET

Related to this story

Topics Injection Molding, Machinery, Molds/Tooling

ST. VALENTIN, AUSTRIA (Oct. 4, 1:45 p.m. ET) — Engel Holding GmbH demonstrated its capability in molding very thin wall parts for electronic products at its symposium in St. Valentin.

Heinz Rasinger, head of Engel’s teletronics business unit, described the molding of a laptop lid with a thickness of less than 1mm as “extreme thin wall technology.”

Such thin walls require high precision molding. At the symposium, Engel showed a new electric version of its two-platen duo range, the 500-metric ton e-duo 2440 machine, producing the laptop demonstrator part in an injection-compression process with in-mold decoration (IMD).

Electric drives on the large scale duo machine enable precision and speed, according to Engel. The e-duo machine can achieve opening and closing speeds of up to 1,000mm/s.

The 500-metric ton e-duo at the symposium produced the laptop lid in a cycle time of 35s. The operator ensures parallel closing through the control of pressure pads on each of the four tiebars which can be adjusted individually.

Bayer MaterialScience supplied the scratchproof coated PC foil and PC carrier for the demonstrator part. Rasinger said that IMD foils for this technology also need to be very thin and the foil was only 20 microns in the application he showed to European Plastics News.

IMD allows injection molders to respond to a growing trend in consumer electronics towards customization. Rasinger said: “The challenge for the manufacturer now is to create premium, individually-decorated surfaces while at the same time reducing the component size and weight.”

Consumers’ own photos can be applied onto laptops and mobile phone covers. For this development, Engel collaborated with Monterey, Calif.-based in-mold decoration company ZoMazz Inc., Rasinger said.

Engel’s other partners in this project were: Inmold, part of Uniplas, based in Singapore (mold); and Max Petek, based in Radolfzell, Germany (clean room).

The clean room enclosure shown at the symposium also demonstrated advances Engel has made in tackling dust and dirt contamination of IMD foils. Despite cleanroom technology, the reject rate in IMD is “frequently still too high”, the company says.

In the enclosure at the side of the e-duo machine, Engel demonstrated an automated double brush system for cleaning the foil.

An Engel easix robot first places the foil for brushing at a separate station. It then moves it to a second brush located very close to the mold space. This close proximity reduces the possibility of dust attaching to the foil before molding.

Thin wall molding was also the focus of another application demonstrated at the Engel symposium: the front cover of Amazon’s Kindle e-reader, which measures just 0.4 mm at the thinnest part.

A 200-metric ton e-motion 940 machine produced the matt grey PC/ABS cover during the demonstration in a cycle time of 29s using variotherm technology. Engel says the machine is suited to the parallel operation of the individual electric drives which keeps the cycle times low despite variotherm technology.

The most familiar variotherm applications have a glossy piano black finish, but Rasinger said: “Achieving a matt finish is even trickier than a gloss finish.”

Very thin wall moldings often have sink marks and flow lines, but the variotherm process ensured this was not the case in the Kindle application, even with variation in wall thickness across the component.

Engel’s partner in the project was RocTool, based in Le Bourget du Lac, France, which supplied the mold and inductive-variothermal mold temperature control system. RocTool’s system includes an integrated interface with the molding machine control.

Rasinger said the Kindle application has been molded in this way by a company in Huhai, China, since last year. Previously, the part was produced using a steam molding process, but he said the new method was chosen because of a faster cycle time.

Engel demonstrated benefits of MuCell microcellular foam molding on a plug housing application made with Lanxess Durethan B4300 PBT/ASA material containing 30 percent glass fiber. The part was molded on a 90-metric ton e-victory 310 electric machine in a cycle time of 33s.

Rasinger said warpage is considerably reduced by using the MuCell technology, in which holding pressure is aided by the foaming process. In addition to dimensional stability, using MuCell technology led to a 10 percent reduction in material used and a 10 percent reduction in cycle time, he said.

Engel’s project partner for the application was connector molder FCI, based in Mattighofen, Austria.


Comments

Engel shows molding for electronic parts

David Eldridge

Published: October 4, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

CPM Extrusion, ECON launch new line of underwater pelletizers

April 23, 2014 11:25 am ET

CPM Extrusion Group and ECON GmbH unveiled their brand new EUPC line of underwater pelletizers today at ChinaPlas held in Shanghai, China.    More

Image

How CEO Santi is changing ITW

April 23, 2014 2:48 pm ET

Scott Santi is showing he can do more than just cut costs at Illinois Tool Works Inc.    More

Image

China's mold making sector plodding forward

April 23, 2014 1:25 pm ET

With the Dow Jones Industrial Average reaching new highs, China's similar indexes are still hovering at a low level. What does the economic barometer ...    More

Image

TSM growing into a second generation of leadership

April 23, 2014 12:50 pm ET

This is a time of great growth for the Dundalk, Ireland-based TSM Control Systems, a company that has created a name for itself since 1977 by...    More

Image

HRS adding more North American production for hot runners

April 22, 2014 12:57 pm ET

An Italian tooling component supplier is set to open a new production plant in Grand Rapids, Mich. The HRS Flow Division of San Polo di Piace-headquar...    More

Market Reports

Market Data Book - Rankings & Lists

A one-stop download of Plastic News' exclusive annual lists and processor rankings containing essential data including sales, employees, end markets, materials and more.
EXCLUSIVE EXCEL FEATURE: full mailing address details for available plant locations.

Learn more

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report provides analysis and discussions of economic and political conditions, market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as strategies being implemented by thermoformed packaging companies. In addition, there are reviews of 25 leading thermoformers in the packaging segment, assessing their growth initiatives and performance metrics over 10 years.

Learn more

Mold Making and Tooling Review and Outlook 2014 North America

This report provides in-depth analysis of the mold and toolmaking market for North America, including discussions of trends, opportunities, threats, the latest developments in production and labor and equipment trends impacting moldmakers.

Learn more

Upcoming Plastics News Events

May 6, 2014 - May 8, 2014Plastics in Medical Devices 2014

May 12, 2014 - May 12, 2014Plastics News Brazil Pharma Summit

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

February 3, 2015 - February 7, 2015Plastics News Executive Forum 2015

More Events