Engel shows molding for electronic parts

David Eldridge

Published: October 4, 2012 6:00 am ET

Related to this story

Topics Injection Molding, Machinery, Molds/Tooling

ST. VALENTIN, AUSTRIA (Oct. 4, 1:45 p.m. ET) — Engel Holding GmbH demonstrated its capability in molding very thin wall parts for electronic products at its symposium in St. Valentin.

Heinz Rasinger, head of Engel’s teletronics business unit, described the molding of a laptop lid with a thickness of less than 1mm as “extreme thin wall technology.”

Such thin walls require high precision molding. At the symposium, Engel showed a new electric version of its two-platen duo range, the 500-metric ton e-duo 2440 machine, producing the laptop demonstrator part in an injection-compression process with in-mold decoration (IMD).

Electric drives on the large scale duo machine enable precision and speed, according to Engel. The e-duo machine can achieve opening and closing speeds of up to 1,000mm/s.

The 500-metric ton e-duo at the symposium produced the laptop lid in a cycle time of 35s. The operator ensures parallel closing through the control of pressure pads on each of the four tiebars which can be adjusted individually.

Bayer MaterialScience supplied the scratchproof coated PC foil and PC carrier for the demonstrator part. Rasinger said that IMD foils for this technology also need to be very thin and the foil was only 20 microns in the application he showed to European Plastics News.

IMD allows injection molders to respond to a growing trend in consumer electronics towards customization. Rasinger said: “The challenge for the manufacturer now is to create premium, individually-decorated surfaces while at the same time reducing the component size and weight.”

Consumers’ own photos can be applied onto laptops and mobile phone covers. For this development, Engel collaborated with Monterey, Calif.-based in-mold decoration company ZoMazz Inc., Rasinger said.

Engel’s other partners in this project were: Inmold, part of Uniplas, based in Singapore (mold); and Max Petek, based in Radolfzell, Germany (clean room).

The clean room enclosure shown at the symposium also demonstrated advances Engel has made in tackling dust and dirt contamination of IMD foils. Despite cleanroom technology, the reject rate in IMD is “frequently still too high”, the company says.

In the enclosure at the side of the e-duo machine, Engel demonstrated an automated double brush system for cleaning the foil.

An Engel easix robot first places the foil for brushing at a separate station. It then moves it to a second brush located very close to the mold space. This close proximity reduces the possibility of dust attaching to the foil before molding.

Thin wall molding was also the focus of another application demonstrated at the Engel symposium: the front cover of Amazon’s Kindle e-reader, which measures just 0.4 mm at the thinnest part.

A 200-metric ton e-motion 940 machine produced the matt grey PC/ABS cover during the demonstration in a cycle time of 29s using variotherm technology. Engel says the machine is suited to the parallel operation of the individual electric drives which keeps the cycle times low despite variotherm technology.

The most familiar variotherm applications have a glossy piano black finish, but Rasinger said: “Achieving a matt finish is even trickier than a gloss finish.”

Very thin wall moldings often have sink marks and flow lines, but the variotherm process ensured this was not the case in the Kindle application, even with variation in wall thickness across the component.

Engel’s partner in the project was RocTool, based in Le Bourget du Lac, France, which supplied the mold and inductive-variothermal mold temperature control system. RocTool’s system includes an integrated interface with the molding machine control.

Rasinger said the Kindle application has been molded in this way by a company in Huhai, China, since last year. Previously, the part was produced using a steam molding process, but he said the new method was chosen because of a faster cycle time.

Engel demonstrated benefits of MuCell microcellular foam molding on a plug housing application made with Lanxess Durethan B4300 PBT/ASA material containing 30 percent glass fiber. The part was molded on a 90-metric ton e-victory 310 electric machine in a cycle time of 33s.

Rasinger said warpage is considerably reduced by using the MuCell technology, in which holding pressure is aided by the foaming process. In addition to dimensional stability, using MuCell technology led to a 10 percent reduction in material used and a 10 percent reduction in cycle time, he said.

Engel’s project partner for the application was connector molder FCI, based in Mattighofen, Austria.


Comments

Engel shows molding for electronic parts

David Eldridge

Published: October 4, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Baxter investing $300 million to expand dialyzers production in Alabama

August 29, 2014 12:53 pm ET

Baxter International, Inc. is expanding its Opelika, Ala. manufacturing location to boost production of dialyzers, a key component of hemodialysis...    More

Image

Obituary: Jerry Williams, Prism Plastics co-owner

August 29, 2014 8:50 am ET

Williams founded Prism Plastics with Rod Bricker and Gerry Phillips, after the three left Huron Plastics Group in 1999.    More

Image

Haitian's standardization efforts paying off

August 29, 2014 9:53 am ET

Streamlined design efforts and robust export sales helped propel Ningbo, China-based injection molding machine manufacturer Haitian International...    More

Image

American Starlinger-Sahm begins work on new US headquarters

August 29, 2014 10:18 am ET

American Starlinger-Sahm Inc., which sells equipment for woven plastic bag production, PET recycling equipment, sheet extrusion and laminating lines...    More

Polish injection molder Teknorubber up for sale

August 29, 2014 9:14 am ET

Polish plastic parts maker Teknorubber has been put up for sale following its insolvency filing in March 2014. The company is to be auctioned through ...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events