Carbon fiber a hit in Paris

By Rhoda Miel
News Editor

Published: October 4, 2012 6:00 am ET

Light-weight carbon fiber is used extensively in the SLS AMG Coupé, helping the electric-drive car reach speeds of 155 mph. (Daimler AG photo)

Related to this story

Topics Automotive, Sustainability, Materials, Suppliers

PARIS (Oct. 4, 3:20 p.m. ET) — New uses for plastics are hitting the road in Europe, from high-end sports cars to the family van.

At the press preview for the Paris Motor Show — officially the Mondial de l’Automobile — Daimler AG rolled out its all-electric Mercedes SLS AMG Coupé Electric Drive, which boasts extensive use of carbon fiber to help it offer up speeds of up to 155 mph, and a 155-mile range on its lithium-ion batteries.

The production car was shown alongside two other vehicle concepts — the B-Class Electric Drive sedan and a natural gas-driven version of the B-Class — and the electric-drive Smart Brabus.

The Mercedes builds on the Stuttgart, Germany-based auto­maker’s E-Cell design for electric vehicles, which creates a carbon-fiber “spine” that runs along the floor of the car and holds the battery pack. The carbon fiber is both light and strong enough to protect the batteries during a crash.

Daimler first showed the carbon-fiber-spine concepts in 2011, saying the composite is 50 percent lighter than a comparable steel package and 30 percent lighter than aluminum.

The AMG electric car will have 12 battery modules, each with 72 individual lithium-ion cells for a total of 865 cells. Both the cells and the liquid-cooling system for the battery use plastics extensively in frames, connectors, ducts and other components.

The batteries power four individual electric motors in an all-wheel-drive system.

The sports car also boasts carbon fiber throughout its body. A front splitter is designed to create a downforce on the front axle to improve performance. The front mirrors and the engine cover are also produced with carbon fiber.

A far-less-expensive electric car, the Neoma EV, is set to go on the road from French automaker Lumeneo using lithium-ion batteries supplied by Midland, Mich.-based Dow Kokam.

The compact car is less than 10 feet long and has a range of up to 87 miles with the battery system. It can hit speeds up to 68 miles per hour, but is targeted at urban drivers.

Production has already begun, meanwhile, on a new car for the European market. Rather than power and speed, Ford Motor Co. boasts convenience and an easier way to get the kids in the car with its B-Max.

Dearborn, Mich.-based Ford created the small minivan without a traditional B-pillar — the vertical structural support between the first and second row of seats.

Removing the pillar and replacing the traditional rear door with a sliding door allows van users to get into the rear seats more easily. That makes it easier to get children into car seats or large packages in and out of the vehicle. But removing the B-pillar also eliminated the traditional location for front-row seat belts.

Seat supplier Johnson Controls Inc. had to design a front seat that integrated the seat-belt mechanism and developed all-new production at new sites in Romania, near Ford’s assembly plant in Craiova.

JCI, with auto­mo­tive operations based in Plymouth, Mich., and European offices in Bur­scheid, Germany, hired 185 people for the seat-assembly plant in Craiova. It also bought Romania’s Spumotim SA in late 2011, adding its urethane foam facility in Timisoara to produce seat pads for the B-Max seats.

Carbon fiber technologies will be a featured at the Plastics in Lightweight Vehicles 2012 conference, Nov. 6-7 in Livonia, Mich. For information see www.plasticsnews.com/plv2012.


Comments

Carbon fiber a hit in Paris

By Rhoda Miel
News Editor

Published: October 4, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Ohio molder sold to private equity firm

August 19, 2014 5:23 pm ET

Private equity firm TVV Capital of Nashville has acquired injection molder Design Molded Plastics Inc. for an undisclosed price.    More

Image

Pactiv selling building products unit to Ireland's Kingspan

August 19, 2014 3:54 pm ET

Irish building material manufacturer Kingspan Group plc is acquiring the insulation business of Lake Forest, Ill.-based Pactiv Building Products for...    More

Image

Flexible film waste-to-oil pilot project continuing in California

August 19, 2014 3:19 pm ET

A recent decision to discontinue operations at a plastics waste-to-oil site in Portland, Ore., is not impacting a pilot program aimed at hard-to-...    More

Image

Germany's Bolta building $50 million plating plant in Alabama

August 19, 2014 2:21 pm ET

A German company is setting up a plastics chrome plating plant in Tuscaloosa, Ala.    More

Image

ISO publishes international standard for measuring phthalates in toys

August 19, 2014 10:40 am ET

The Geneva-based International Organization for Standardization (ISO) has published an international standard on phthalates used as plasticizers in to...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events