Polyethylene to see more use during switch to 1-piece caps

Published: October 5, 2012 6:00 am ET

Ashish Chitalia, project manager at Houston-based Chemical Market Resources Inc., speaks at the Caps & Closures conference. (Plastics News photo by Michael A. Marcotte)

Related to this story

Topics Materials, Suppliers, Packaging

LINCOLNSHIRE, ILL. (Oct. 5, 3:05 p.m. ET) — The one-piece cap is coming to America.

In the U.S., processors use injected molded, high density polyethylene closures to cap water bottles. However, carbonated soft drinks and hot-fill applications are usually topped with compression molded, two-piece closures — an outer polypropylene shell and a liner, usually made from ethylene vinyl acetate.

The U.S. preference for two-piece caps is unique — one-piece closures are common on soft drinks in other locations, primarily Europe and Asia — and the market’s tastes are starting to shift, according to experts who spoke at Plastics News’ Caps & Closures 2012, held Sept. 18-19 in Lincolnshire.

One-piece closures “will be the next big thing to hit the U.S.,” said Mike Sansoucy, president of Netstal Machinery Inc. in Devens, Mass.

Improved materials and closures design has led to the creation of one-piece caps that offer the same sealing surface as two-piece closures, allowing the caps to be used in carbonated soft drink and hot-fill applications, Sansoucy said.

Switching from a two-piece to a one-piece closure requires changing both material and manufacturing process, and, according to the experts, these changes offer several economical and environmental advantages.

PE, made of natural gas feedstock, is now a more cost-effective material than PP. The material also has a balance of toughness and stiffness that can make it a prime replacement for PP in most applications, said Eric Vignola, research and development manager for PE products at Nova Chemicals Corp. of Calgary, Alberta.

“There’s lots of opportunities for innovation, lots of opportunities for [PE] displacing poly­propylene in applications traditionally reserved for PP,” Vignola said.

And processors are taking advantage of those opportunities — HDPE is the fastest-growing material in the caps and closures arena and it’s taking some of that market share from PP, partly thanks to the growing one-piece market, said Ashish Chitalia, project manager at Houston-based Chemical Market Resources Inc.

Since making the switch eliminates the need for an EVA liner, the caps are easier to recycle and the one-step process makes manufacturing more sustainable, Sansoucy said.

“If you can injection mold the cap finished, that’s that. You don’t have to add an extra step, so just from a manufacturing standpoint, it’s a greener solution,” he said.

Sustainability has been an ongoing trend in the caps and closures market, and has driven machine manufacturers to create smaller systems for smaller, strategically located plants, Sansoucy said.

It has also pushed the creation of increasingly lighter caps and closures. In five years, single-piece water-bottle caps have shrunk from an average of 1.45 grams to an average of 0.85 gram, while carbonated soft drink caps have gone from 4.5 grams on average to 2.65 grams, he said.

 “I don’t know how much lighter you can go on a still-water cap … before you’ve just got a bag with a flap on top of it,” Sansoucy joked.

Switching to one-piece caps can eliminate material in both the cap and the bottle, said Lothar Brauer, marketing and business development director at Bericap GmbH & Co. KG.

To support both the weight of a two-piece cap and the torque needed to seal it, bottles used in hot-fill applications need to have heavier and more robust neck finishes — typically about 8.2 grams, Brauer said.

One-piece closures, like the ones designed by Bericap, are lighter weight, feature a large seal angle and are designed to require less torque, so neck finishes can be lighter, he said. He added that replacing two-piece caps with one-piece caps designed by Bericap could reduce resin by 6 tons and carbon output by 17 tons per 500 million bottles.

But the switch to one-piece closures isn’t necessarily an easy one.

The move from PP to PE can be challenging, Nova’s Vignola said. While there’s a wealth of knowledge about using PP in caps and closures applications, there isn’t the same awareness about PE, he added.

Comparing the properties of a PP resin and PE resin can be tricky because the two materials “don’t speak the same language,” he said.

For example, flow in PP resins is measured as melt-flow rate while in PE resins it’s measured as melt index, he said. “The dangerous thing here is that they’re measured at different temperatures, so if you’re comparing two data sheets, you’re not comparing apples to apples.”

Going to injection molded one-piece caps also means an entirely new production system, Sansoucy said.

The transition will require the entire supply chain to get involved. The liner in two-piece caps covers “a multitude of sins on the bottle side,” so processors will need to ensure they’re making bottles correctly, he said.

Even with the hurdles, brands will probably start switching to one-piece caps in the next year or so, Sansoucy said. “It’s going to take brand owners, and maybe it’s not the big players but the smaller players who say we’re willing to risk, or we think it’s time to make that switch away from a lined cap,” he added.


Comments

Polyethylene to see more use during switch to 1-piece caps

Published: October 5, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Citadel opens second compounding facility in China, near Shanghai

January 27, 2015 3:22 pm ET

Citadel Plastics Inc., the American manufacturer of thermoplastic and engineered composite compounds, has opened its second facility in China,...    More

Image

Sales, profit fall at DuPont

January 27, 2015 3:13 pm ET

Materials giant DuPont Co. will use almost all of the proceeds from an upcoming spinoff — one that includes its fluoropolymer and titanium...    More

Image

A. Schulman, Citadel continue buying blitz

January 27, 2015 11:32 am ET

A. Schulman Inc. and Citadel Plastics Inc. — two deal-happy materials firms — were at it again in the second half of 2014.    More

Image

It's becoming a seller's market for plastics firms

January 27, 2015 11:37 am ET

The pace of plastics mergers and acquisitions activity slowed a bit in the second half of 2014 — but market watchers have high expectations for ...    More

Image

Materials market sees more deals

January 27, 2015 11:26 am ET

Plastics materials deals showed modest growth in 2014, increasing 6 percent vs. their 2013 total.    More

Market Reports

Plastics in Automotive: Innovation & Emerging Trends

This special report newly released by PN and sponsored by The Conair Group examines current trends in the use of plastics in automotive, materials innovations and the changing landscape. It includes a review of legislative/regulatory activity impacting vehicle development and lightweighting, market opportunities & challenges for mold and toolmakers, innovative design strategies being implemented by major OEMs and suppliers, as well as a review of key indicators in Canada, Mexico, Brazil and China.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Upcoming Plastics News Events

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events