PETRA proposes new way to judge materials' recyclability

Mike Verespej

Published: October 16, 2012 6:00 am ET

Related to this story

Topics Materials, Public Policy, Sustainability, Recycling, Design

NEW YORK (Oct. 16, 12:15 p.m. ET) — To overcome recycling test barriers that discourage improvements in PET resin, the PET Resin Association has developed a recyclability assessment model that it said is a more “realistic and effective method for assessing recyclability” of various types of PET resin than the guidelines from the Association of Postconsumer Plastic Recyclers.

The PETRA model integrates the need for continued innovation with stringent resin testing and monitoring, said Ralph Vasami, executive director of PETRA, which represents North American producers of PET resin.

The group announced its Recyclability and Innovation Model and posted it online Oct. 16. The document provides voluntary criteria for testing, evaluating and ensuring the recyclability of newly developed PET resins that are used in manufacturing PET bottles and containers.

New York-based PETRA said it issued the model when “it became apparent” — three years after discussions between the two organizations became in 2009 — “that APR was unwilling to change its protocol to allow for the introduction of resin variations anticipated for relatively low market presence, even if offset by additional recyclability safeguards.”

The PETRA model allows for testing variations at levels of 2 percent and 10 percent, which PETRA said encompasses the vast majority of today’s new PET resin variants. 

Current recyclability guidelines in the PET Bottle Critical Guidance document from the Association of Postconsumer Plastic Recyclers call for resin testing at concentrations of either 25 percent or 50 percent. The European PET Bottle Platform PET Recycling Test Protocol allows for testing at lower concentrations than APR.

“APR requires resin variants and innovations typically having a low market presence to meet the same requirements of a resin accounting for 25 percent or 50 percent of total North American PET production,” said PETRA.

Those requirements discourage innovation, make product differentiation difficult and preclude the introduction of resin improvements, PETRA said.

“In recent years, the APR’s focus on defining recyclability in terms of meeting the capabilities of the least-sophisticated recycling operations has been increasingly at odds with advances in resin science and resulting innovations.”

PETRA’s model focuses on real-market resin performance and the evaluation needs of producers, brand owners and recyclers, said Vasami.

In addition to special-use resins, PETRA’s model does include criteria for testing at those more robust levels of 25 percent and 50 percent.

In general, PETRA said its model is designed to combine the most progressive elements of the existing European PET Bottle Platform recyclability guidelines and the APR recycling guidelines for North America — without sacrificing rigorous testing benchmarks or compromising innovation.

PETRA stressed that under its model all innovations will be tested to the same performance criteria and given either a pass or fail mark.

According to PETRA, its model includes:

* A rigorous test protocol to measure recyclability in terms of a resin’s physical and chemical performance characteristics.

* A dispersion assessment, based on the test protocol results, that calculates the volume of a resin type that can safely be placed in the marketplace without compromising the overall recyclability of PET.

* The provision of control resins that reflect the current North American supply of water-grade and carbonated soft drink-grade PET resins, for use with the test protocol.

* Annual test monitoring — once the model is in prevalent use — of the combined virgin PET stream to identify and quantify any changes in the virgin resin stream that might adversely impact the recyclability of PET.

Under the program, PETRA will provide industry-representative control resins to organizations that use the model for testing. Once the model is widely used, PETRA said it will be committed to funding annual third-party testing and monitoring of the PET resin stream.


Comments

PETRA proposes new way to judge materials' recyclability

Mike Verespej

Published: October 16, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Vinyl siding's lead slips, but industry pushing back

July 29, 2014 2:04 pm ET

Vinyl siding continues to be the top cladding choice for home builders and remodelers but fiber cement is gaining ground — at an alarming rate...    More

Unipex Group buys Ferguson Chemical Innovation

July 29, 2014 1:57 pm ET

Chemical distributor Unipex Group Inc. announced July 29 that it had purchased Ferguson Chemical Innovation, a Brampton, Ontario-based supplier of...    More

Image

Carbon black supplier Orion begins trading on NYSE

July 29, 2014 11:29 am ET

Orion Engineered Carbons S.a.r.l. has priced the initial public offering of 19.5 million common shares at a price to the public of $18 per share.    More

Image

Dow sees solid second quarter performance

July 29, 2014 11:19 am ET

Dow Chemical Co. has reported its second quarter figures, with its seventh consecutive quarter of growth, according to the company.More

Image

Evonik sells polyimide foams operation to Boyd

July 29, 2014 10:46 am ET

Modesto, Calif.-based Boyd Corp., a manufacturers of specialty material and sealing agents, has purchased Evonik Industries’ Solimid...    More

Market Reports

Plastics Recyclers Data Report & Directory

This exclusive MS Excel database contains all the companies from Plastics News' ranking of top North American Recyclers and Brokers by reprocessed volume and also includes a directory with materials processes, services offered and company contact information. Data is based on primary research by PN editorial staff.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events