PETRA proposes new way to judge materials' recyclability

Mike Verespej

Published: October 16, 2012 6:00 am ET

Related to this story

Topics Sustainability Public Policy Materials Recycling Design
Companies & Associations

NEW YORK (Oct. 16, 12:15 p.m. ET) — To overcome recycling test barriers that discourage improvements in PET resin, the PET Resin Association has developed a recyclability assessment model that it said is a more “realistic and effective method for assessing recyclability” of various types of PET resin than the guidelines from the Association of Postconsumer Plastic Recyclers.

The PETRA model integrates the need for continued innovation with stringent resin testing and monitoring, said Ralph Vasami, executive director of PETRA, which represents North American producers of PET resin.

The group announced its Recyclability and Innovation Model and posted it online Oct. 16. The document provides voluntary criteria for testing, evaluating and ensuring the recyclability of newly developed PET resins that are used in manufacturing PET bottles and containers.

New York-based PETRA said it issued the model when “it became apparent” — three years after discussions between the two organizations became in 2009 — “that APR was unwilling to change its protocol to allow for the introduction of resin variations anticipated for relatively low market presence, even if offset by additional recyclability safeguards.”

The PETRA model allows for testing variations at levels of 2 percent and 10 percent, which PETRA said encompasses the vast majority of today’s new PET resin variants. 

Current recyclability guidelines in the PET Bottle Critical Guidance document from the Association of Postconsumer Plastic Recyclers call for resin testing at concentrations of either 25 percent or 50 percent. The European PET Bottle Platform PET Recycling Test Protocol allows for testing at lower concentrations than APR.

“APR requires resin variants and innovations typically having a low market presence to meet the same requirements of a resin accounting for 25 percent or 50 percent of total North American PET production,” said PETRA.

Those requirements discourage innovation, make product differentiation difficult and preclude the introduction of resin improvements, PETRA said.

“In recent years, the APR’s focus on defining recyclability in terms of meeting the capabilities of the least-sophisticated recycling operations has been increasingly at odds with advances in resin science and resulting innovations.”

PETRA’s model focuses on real-market resin performance and the evaluation needs of producers, brand owners and recyclers, said Vasami.

In addition to special-use resins, PETRA’s model does include criteria for testing at those more robust levels of 25 percent and 50 percent.

In general, PETRA said its model is designed to combine the most progressive elements of the existing European PET Bottle Platform recyclability guidelines and the APR recycling guidelines for North America — without sacrificing rigorous testing benchmarks or compromising innovation.

PETRA stressed that under its model all innovations will be tested to the same performance criteria and given either a pass or fail mark.

According to PETRA, its model includes:

* A rigorous test protocol to measure recyclability in terms of a resin’s physical and chemical performance characteristics.

* A dispersion assessment, based on the test protocol results, that calculates the volume of a resin type that can safely be placed in the marketplace without compromising the overall recyclability of PET.

* The provision of control resins that reflect the current North American supply of water-grade and carbonated soft drink-grade PET resins, for use with the test protocol.

* Annual test monitoring — once the model is in prevalent use — of the combined virgin PET stream to identify and quantify any changes in the virgin resin stream that might adversely impact the recyclability of PET.

Under the program, PETRA will provide industry-representative control resins to organizations that use the model for testing. Once the model is widely used, PETRA said it will be committed to funding annual third-party testing and monitoring of the PET resin stream.


Comments

PETRA proposes new way to judge materials' recyclability

Mike Verespej

Published: October 16, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

KHS cuts packaging with direct printing on PET bottles, adhesive multi-packs

April 23, 2015 1:39 pm ET

KHS GmbH has been pouring a lot of time into solving issues related to direct printing on PET bottles, and after eight years of work, everyone...    More

Image

DuPont center in India gets LEED Certification

April 23, 2015 1:07 pm ET

DuPont Co.'s Knowledge Center in Hyderabad, India, was awarded LEED certification by the U.S. Green Building Council.    More

Image

MeadWestvaco joins the Recycling Partnership

April 23, 2015 11:19 am ET

MeadWestvaco Corp., a global packaging company with some operations in plastics, is joining the Recycling Partnership.    More

Image

DaVinci puts its plastic scrap back to work on new roofs

April 22, 2015 3:01 pm ET

From its own manufacturing facility to construction sites around the United States, DaVinci Roofscapes recycles about 300,000 pounds of polymer scrap ...    More

Image

Obama cites plastics-to-oil firm, meets CEO

April 22, 2015 2:20 pm ET

Plastics-to-oil firm Vadxx Energy LLC was in the Presidential spotlight on March 18.    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 15, 2015 - September 17, 2015Plastics Caps & Closures - September 2015

More Events