PETRA proposes new way to judge materials' recyclability

Mike Verespej

Published: October 16, 2012 6:00 am ET

Related to this story

Topics Sustainability, Public Policy, Materials, Recycling, Design

NEW YORK (Oct. 16, 12:15 p.m. ET) — To overcome recycling test barriers that discourage improvements in PET resin, the PET Resin Association has developed a recyclability assessment model that it said is a more “realistic and effective method for assessing recyclability” of various types of PET resin than the guidelines from the Association of Postconsumer Plastic Recyclers.

The PETRA model integrates the need for continued innovation with stringent resin testing and monitoring, said Ralph Vasami, executive director of PETRA, which represents North American producers of PET resin.

The group announced its Recyclability and Innovation Model and posted it online Oct. 16. The document provides voluntary criteria for testing, evaluating and ensuring the recyclability of newly developed PET resins that are used in manufacturing PET bottles and containers.

New York-based PETRA said it issued the model when “it became apparent” — three years after discussions between the two organizations became in 2009 — “that APR was unwilling to change its protocol to allow for the introduction of resin variations anticipated for relatively low market presence, even if offset by additional recyclability safeguards.”

The PETRA model allows for testing variations at levels of 2 percent and 10 percent, which PETRA said encompasses the vast majority of today’s new PET resin variants. 

Current recyclability guidelines in the PET Bottle Critical Guidance document from the Association of Postconsumer Plastic Recyclers call for resin testing at concentrations of either 25 percent or 50 percent. The European PET Bottle Platform PET Recycling Test Protocol allows for testing at lower concentrations than APR.

“APR requires resin variants and innovations typically having a low market presence to meet the same requirements of a resin accounting for 25 percent or 50 percent of total North American PET production,” said PETRA.

Those requirements discourage innovation, make product differentiation difficult and preclude the introduction of resin improvements, PETRA said.

“In recent years, the APR’s focus on defining recyclability in terms of meeting the capabilities of the least-sophisticated recycling operations has been increasingly at odds with advances in resin science and resulting innovations.”

PETRA’s model focuses on real-market resin performance and the evaluation needs of producers, brand owners and recyclers, said Vasami.

In addition to special-use resins, PETRA’s model does include criteria for testing at those more robust levels of 25 percent and 50 percent.

In general, PETRA said its model is designed to combine the most progressive elements of the existing European PET Bottle Platform recyclability guidelines and the APR recycling guidelines for North America — without sacrificing rigorous testing benchmarks or compromising innovation.

PETRA stressed that under its model all innovations will be tested to the same performance criteria and given either a pass or fail mark.

According to PETRA, its model includes:

* A rigorous test protocol to measure recyclability in terms of a resin’s physical and chemical performance characteristics.

* A dispersion assessment, based on the test protocol results, that calculates the volume of a resin type that can safely be placed in the marketplace without compromising the overall recyclability of PET.

* The provision of control resins that reflect the current North American supply of water-grade and carbonated soft drink-grade PET resins, for use with the test protocol.

* Annual test monitoring — once the model is in prevalent use — of the combined virgin PET stream to identify and quantify any changes in the virgin resin stream that might adversely impact the recyclability of PET.

Under the program, PETRA will provide industry-representative control resins to organizations that use the model for testing. Once the model is widely used, PETRA said it will be committed to funding annual third-party testing and monitoring of the PET resin stream.


Comments

PETRA proposes new way to judge materials' recyclability

Mike Verespej

Published: October 16, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Brown signs California's plastic bag ban into law

September 30, 2014 1:38 pm ET

Gov. Jerry Brown (D) made it official today: plastic bags are banned across the entire state of California.    More

Image

New Hexcel plant will supply carbon fiber for Airbus A350 XWB

September 30, 2014 2:43 pm ET

Hexcel Corp. is investing $250 million on a new carbon fiber plant in France, with part of the production going into the future Airbus SAS A350 XWB.    More

Image

LyondellBasell CEO Gallogly to retire

September 30, 2014 3:00 pm ET

James Gallogly, CEO of Houston-based polyolefins producer LyondellBasell Industries NV, on Sept. 29 announced plans to retire in 2015.    More

Image

Toyoda Gosei pleads guilty, agrees to $26 million fine for price fixing

September 30, 2014 11:27 am ET

Toyoda Gosei Co. Ltd. has pleaded guilty and agreed to pay a $26 million fine for its alleged role in an international conspiracy to rig bids and fix ...    More

Image

Audacious vandal stuns Taipei Plas

September 29, 2014 4:59 pm ET

Melodrama erupted at the traditionally tranquil Taipei Plas trade show on Sept. 28 when a mysterious intruder flung red paint at the Baumüller Automat...    More

Market Reports

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our industry analysis highlights macro industry trends and micro trends faced by companies that do business in Mexico. The report also provides key industry statistics and forecasts to anticipate future industry expansion.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Injection Molders Market Report & Ranking 2014

This special package contains our 132-page 2014 Market Report on the Injection Molding segment and our exclusive 2014 RANKINGS database of 500+ Injection Molders for a discounted package price.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events