Thai processors urged to look to ASEAN for growth

By Steve Toloken
Staff Reporter / Asia Bureau Chief

Published: October 19, 2012 6:00 am ET

Related to this story

Topics Materials, Public Policy, Suppliers

BANGKOK (Oct. 19, 3:45 a.m. ET) — Thailand's plastics processing industry, the largest in Southeast Asia, should look for closer economic integration with its neighbors as a "new model of sustained growth" to broaden beyond traditional export markets and cope with a slower world economy, industry officials said at a recent conference.

Speaking at the Flexpo Bangkok conference, held Sept. 17-19 in Bangkok, Thai industry officials said that overall the country's plastics product sector grew last year to 255 billion Baht (US$8.3 billion), up from about 225 billion Baht ($7.3 billion) in 2010.

But that was still below the roughly 280 billion Baht (US$ 9.1 billion) in revenues the sector had in 2007, before the global financial crisis, according to figures from the Petroleum Institute of Thailand given at the conference.

That prompted some officials to suggest that a full recovery should look more to the 10-member Association of Southeast Asian Nations and its rapid urbanization and expanding middle class.

By 2015, those 10 countries expect to launch the ASEAN Economic Community and create a single market among their 600 million people.

"In 2015, we think ASEAN will be a very solid framework for a new model of sustained growth for the ASEAN countries," said Siri Jirapongphan, executive director of the Bangkok-based Petroleum Institute of Thailand. "Our industrial members are focusing their further development and growth in this region."

The top four export markets for Thailand’s plastics processing industry in 2011 were Japan, the United States, China, and Australia, and they will remain important, Jiripongphan and others said.

But with the middle class in ASEAN expected to grow from 24 percent of the population now to 65 percent by 2030, and an urbanization rate that is projected to grow from 42 percent ASEAN-wide now to 50 percent by 2025, regional opportunities are rising, said Petch Niyomsen, polyolefins strategy and planning manager with Bangkok-based SCG Chemicals.

"There's a huge potential for us to capture, if we can develop the right strategy in those countries," said Chaya Chandavasu, vice president, science and innovation department, PTT Global Chemical Ltd.  "It will be very useful to build a stronger plastics industry in the region."

He said the AEC will make it easier for both labor and production to flow across the 10 member countries and create a single market.

Still, Thai manufacturing is overwhelmingly export focused, with just 22 percent of its output going to its domestic market, Niyomsen said. Thailand is ASEAN’s largest maker of both autos and electronics, with large assembly plants for American and Japanese car makers.

In spite of that industrial base, figures from the Petroleum Institute suggest that Thailand's plastics processing sector has lost some ground to neighboring Malaysia, which edged past Thailand in 2011 to be ASEAN‘s top plastic products exporter.

Part of that slip in ranking was from disruptions to supply chains caused by court rulings delaying expansion of the Map Ta Phut Industrial Estate, the country’s largest petrochemical park, said Khunying Thongtip Ratanarat, a board member of the Bangkok-based Petroleum Institute of Thailand Foundation. Those court rulings came after environmental lawsuits against pollution halted the expansions.

"The growth in the last five years or so in the conversion industry has slowed down a bit because of political instability," she said, referring to the court cases. "It's nothing much that serious but certainly while we were stagnating, Malaysia was taking that opportunity."

Jirapongphan and other PIT officials at Flexpo said the industry faces other challenges, such as not spending enough on research and development and sometimes lacking scale to be more competitive globally.

He said that many Thai companies generally spend less than 0.5 percent of revenues on R&D, when they should be spending 2-3 percent.

"We used to think we have cheap labor," he said. "We are now focusing more on building local manpower competencies."


Comments

Thai processors urged to look to ASEAN for growth

By Steve Toloken
Staff Reporter / Asia Bureau Chief

Published: October 19, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Poor plastic coating prompts cable recall

August 29, 2014 2:10 pm ET

Australia's competition regulator, the Australian Competition and Consumer Commission (ACCC), has ordered a major recall of 2,485 miles of electrical ...    More

Image

EPA fines RI polymer company

August 29, 2014 1:20 pm ET

A Rhode Island polymer manufacturer has reached a $60,000 settlement with the U.S. Environmental Protection Agency (EPA) for violating federal clean...    More

Image

Haitian's standardization efforts paying off

August 29, 2014 9:53 am ET

Streamlined design efforts and robust export sales helped propel Ningbo, China-based injection molding machine manufacturer Haitian International...    More

Image

Updating a travel icon for the professional millennial

August 29, 2014 11:44 am ET

As part of a drive to expand its customer base to include more millennials, Airstream Inc. turned to the Columbus College of Art & Design's...    More

Image

American Starlinger-Sahm begins work on new US headquarters

August 29, 2014 10:18 am ET

American Starlinger-Sahm Inc., which sells equipment for woven plastic bag production, PET recycling equipment, sheet extrusion and laminating lines a...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events