New propylene feedstock could smooth PP pricing curves

By Frank Esposito
Senior Staff Reporter

Published: November 6, 2012 6:00 am ET

Related to this story

Topics Materials, Suppliers

CHICAGO (Nov. 6, 1:25 p.m. ET) — Polypropylene looks to continue traveling down a twisted road — but the addition of on-purpose propylene feedstock in North America might smooth out some of those tricky curves.

On-purpose propylene production — as opposed to the material being made as a by-product of the oil or gas refining process — should increase regional capacity by at least 5 percent and possibly by as much as 35 percent in the next several years, according to industry analyst Esteban Sagel.

Sagel is Americas PP director for the IHS Chemical consulting firm in Houston. He spoke at a Plastics Processors Conference hosted by his firm, Oct. 24-25 in Chicago.

The new propylene might help keep PP production in the region, but it might not do too much to lower prices, Sagel explained.

On-purpose production “moves propylene to a higher cost position,” he said. “But PP will remain expensive vs. other resins that use ethylene as a raw material. (PP) could be as much as 40 percent more expensive in North America.”

“We’re no longer going back to the cheap (PP price) levels of 10-15 years ago, so we have to get used to this.”

Propane dehydrogenation (PDH) will account for 45 percent of on-purpose propylene production, with North America and the Middle East leading the way with that process. In North America, propane is available from shale natural gas.

Use of shale gas “has changed the economic profile of propylene production,” Sagel said. “It will result in investment in PP in North America for the first time in a long time.”

North America is set to become a net importer of PP from 2012-15, but new PP will allow the region to become a net exporter again beginning in 2017.

As much as 7.5 billion pounds of new PP capacity could be added in North America between 2014 and 2019, Sagel said. Most of this new capacity will be aimed at exports. North American demand is growing, he said, But is still affected by volatility in price and demand. New PP capacity in 2014 would improve supply and ease volatility somewhat.

Producers have kept a tight handle on production and inventories in the last two years in North America, Sagel said. “They’ve corrected very rapidly to keep the market tight,” he explained. For 2012, North American PP demand is set to be up 2.9 percent, with export losses dampening domestic demand growth of 5.5 percent.

North American PP prices should peak in 2015, Sagel said, before entering a decline phase that should last until 2019. During this time, integrated PP makers should benefit the most.

Globally, PP remains oversupplied, which should result in relatively low operating rates of 80-84 percent from 2012-17. Most of the excess capacity is in Northeast Asia, where low resin prices are affecting the global market by lowering the cost of finished goods made from PP.

In China, the PP market is becoming more self-sufficient. In 2009, impoted PP supplied 40 percent of China’s needs. By 2017, that total should be down to 13 percent.

Sagel also said that a global PP price may begin to develop in the not-too-distant future. That price would be set by non-integrated PP economics, he said.


Comments

New propylene feedstock could smooth PP pricing curves

By Frank Esposito
Senior Staff Reporter

Published: November 6, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Startup post-consumer recycling specialty company Zzyzx wins grant

September 2, 2014 1:33 pm ET

An Allentown, Pa., company is receiving a grant of $737,000 to help support its efforts to develop polymers using post-consumer plastics.    More

Image

A. Schulman buys Australia's Compco, 10th acquisition in 4 years

September 2, 2014 11:13 am ET

Akron, Ohio-based A. Schulman Inc., a supplier of high-performance plastic compounds and resins, said it has acquired a company near Melbourne,...    More

Image

Battenfeld-Cincinnati secures major Chinese extruder deal

September 2, 2014 10:58 am ET

An undisclosed major Chinese pipe manufacturer has ordered 25 extruders from German-Austrian company Battenfeld-Cincinnati's subsidiary, Battenfeld-...    More

Image

EPA fines RI polymer company

August 29, 2014 1:20 pm ET

A Rhode Island polymer manufacturer has reached a $60,000 settlement with the U.S. Environmental Protection Agency (EPA) for violating federal clean...    More

Image

Haitian's standardization efforts paying off

August 29, 2014 9:53 am ET

Streamlined design efforts and robust export sales helped propel Ningbo, China-based injection molding machine manufacturer Haitian International Hold...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events