KM demos its extrusion lines

By Bill Bregar
Senior Staff Reporter

Published: November 8, 2012 6:00 am ET

Open house attendees watch a KMB single-screw machine with a 75-inch screw diameter extrude thick-wall PE pipe at KraussMaffei’s Kentucky plant. (Plastics News photo by Bill Bregar)

Related to this story

Topics Film & Sheet, Pipe/Profile/Tubing, Machinery

FLORENCE, KY. (Nov. 8, 2:55 p.m. ET) — Germany-based Ettlinger Kunststoffmaschinen GmbH has sold five of its rotation filters to North American customers since it launched Ettlinger North America last year, officials said at a KraussMaffei Corp. open house.

Ettlinger will open a U.S. headquarters by next summer, in the Chicago area, according to Mike Diletti, North American sales manager. The operation will house offices, spare parts and a material testing area, he said. Diletti is looking at locations now.

About 45 people attended the KM open house, held Oct. 4 in Florence. They saw two production lines.

A KraussMaffei Berstorff co-rotating twin-screw extruder, a model ZE 52, fed recycled and off-spec polystyrene into an ERF — Ettlinger rotation filter. KM had added a little polyester to the mix, and the EFR removed it, before moving the clean material to the pelletizer.

The other running KraussMaffei Berstorff extruder was a single-screw machine with a 75-inch screw diameter, making thick-wall, 4-inch polyethylene pipe. The line sported several features to boost productivity and accuracy.

KraussMaffei Berstorff’s internal pipe cooling (IPC) system sucks ambient air through the length of the pipe, to cool the inside of the pipe. That allows the pipe line to run faster, with a shorter cooling zone. The pipe ran through a conventional water cooling area. The PE pipe line also sported equipment from Inoex LLC of Lancaster, Pa. An Inoex ERS 250 ultrasonic measuring system continuously measured wall thickness, diameter, shape and other parameters. The pipe extruder also was equipped with an Inoex feeding system.

The IPC and Inoex instruments — plus downstream equipment such as the haul-off and saw — are all linked through the extruder’s C5 controller. That means, for example, that if the Inoex detects changes in wall thicknesses, it can signal the extruder to change speeds.

“It’s a complete package. It’s all integrated. It’s all talking to each other,” said Mark Giesey, operations manager of KraussMaffei Berstorff’s extrusion division.

Recycling was a major focus of the open house. The Ettlinger-equipped twin-screw ZE extruder had a screw diameter of 52 millimeters and the recycling line was running at 800 pounds an hour.

Martin Mack, vice president of research and development for extrusion at KraussMaffei Berstorff, said co-rotating twin-screw extruders do a good job with recycling of wet plastic scrap that comes from washing operations. “They can handle a large amount of moisture,” he said in a technical presentation at the open house.”

Running PET on a single-screw extruder requires pre-drying, a major investment in equipment, he said.

“With the twin-screw extruder, we do not need the pre-drying step,” Mack said. Moisture gets mechanically removed in the barrel, and vented out. So while the initial cost for the extruder is higher for a twin, the overall operating cost is lower, he said.

Diletti said Ettlinger North America has sold five systems that are in operation at recyclers that do compounding. Two of the customers each have two lines, giving the Ettlinger important repeat business.

Two more sold ERF systems are on boats coming over from Ettlinger headquarters in K"nigsbrunn, Germany, he said. Several other orders are pending, he said.

During a breakout session, Diletti explained what he called the “continuous and stable” operation of the ERF technology.

“It works in a completely different way from other melt filters,” he said.

Most filters push the melt through screens, which need to be frequently flushed. The material from the extruder enters the Ettlinger filter, moving through a rotating drum-shaped filter. On each rotation, contaminants get scraped off by a knife edge. “We’re just constantly cleaning the contamination off the drum, all day,” Diletti said.

Unmelted waste material, such as paper and rubber, gets immediately removed via an auger screw.

Diletti passed around samples of material from one customer that is using an Ettlinger ERF to remove aluminum from a scrap mixture of polystyrene and 20 percent aluminum foil. The recycler then sells the aluminum, he said.

“You’re able to take material that was previously worthless and turn it into something that’s worth quite a bit,” Diletti said.

The speed of the drum gets automatically controlled by pressure sensors — so the unit can speed up if it hits a heavy burst of contaminants.

Constantly cleaning the screen also helps avoid other problems, Diletti said.

“The exit pressure out of the filter is rock solid,” he added.

Some customers in Europe are running from the filter directly into a film line, he said.

Good material passes through holes in the drum-shaped screen, and on to the pelletizer.

Diletti said Ettlinger filters can handle up to 4,000 pounds of material an hour. The company is working on a larger ERF, he said.

“You only change a filter every few weeks or months, depending on what you’re running. And then, you can burn the filter in an oven and reuse it. So the filters last a long time,” Diletti said.


Comments

KM demos its extrusion lines

By Bill Bregar
Senior Staff Reporter

Published: November 8, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Huhtamäki selling film division

November 26, 2014 2:10 pm ET

Private equity firm Deutsche Beteiligungs AG (DBAG) will acquire the film business of Finland-based plastics packaging group Huhtamäki Oyj for 141...    More

Image

Irish packaging group Smurfit Kappa opens film plant in Spain

November 26, 2014 6:00 am ET

Global packaging group Smurfit Kappa Group plc has responded to growing demand for its bag-in-box liquid container/dispensers by opening a new plant...    More

Image

2014 US machinery shipments up 6 percent

November 25, 2014 5:17 pm ET

Through the first nine months of 2014 U.S. shipments of primary plastics equipment — for injection molding, blow molding and extrusion —...    More

Image

Globalization brings sizable growth, primarily in Asia

November 25, 2014 1:40 pm ET

In 1990, the year after Plastics News published our first issue, there were 33,000 injection molding machines sold worldwide. Fast forward to 2013,...    More

Image

Taipei Plas vandal and German firm trade lawsuits

November 25, 2014 1:26 pm ET

Taiwan businessman Karma Tang, who splashed red paint at German firm Baumüller GmbH's Taipei Plas booth, is in a messy legal battle.    More

Market Reports

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 billion plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

October 27, 2015 - October 29, 2015Plastics Financial Summit - New York - 2015

More Events