Stricter standards put fuel tanks under the gun

By Bill Bregar
Senior Staff Reporter

Published: November 13, 2012 6:00 am ET

Related to this story

Topics Blow Molding

PITTSBURGH (Nov. 13, 2:55 p.m. ET) — It took the automotive industry about five years to develop multilayer fuel tanks that could meet California’s LEV II (low-emission vehicle) regulations in the late 1990s, said Mohammad Usman, who leads the computer-aided engineering and material department of Ford Motor Co.’s Powertrain Installations Division.

Stringent emissions standards — for cars and non-automotive small-engine equipment alike — and the transition to hybrid vehicles are some of the challenges facing carmakers and their suppliers today.

And even more-aggressive rules are coming, said Ford’s Usman. The California Air Resources Board is currently working on LEV III, to be phased in over model years 2015 through 2025.

“I’m pretty sure that this requirement that’s coming for the next 10 years is going to be much harder,” Usman said in a presentation last month at the Society of Plastics Engineers’ Blow Molding Conference in Pittsburgh.

Fuel-tank graphicHydrocarbon vapors must be fully contained in a fuel system that is entirely airtight, including the filler pipe, fuel lines and gas tanks, he said. “We want to contain everything in the system and then use it when we drive.”

The move to hybrid vehicles is also “challenging plastic fuel tanks in terms of performance requirements and the need to package batteries and tanks under the vehicle,” said Joel Kopinsky, managing director of ITB Group Ltd., a Novi, Mich.-based consulting company that tracks the global fuel-system business.

In North America, Europe and Japan, virtually all of the automotive plastic fuel tanks are extrusion blow molded, according to ITB. In North America, tanks are six layers and primarily made from high density polyethylene with an ethylene vinyl alcohol layer. In 2012, ITB projects that about 13.3 million North American vehicles will have been outfitted with HDPE tanks, Kopinsky said in a Nov. 8 email.

Washington-based American Chemistry Council data shows U.S./Canadian HDPE resin sales for blow molded auto fuel tanks up 15.7 percent for the first nine months of this year— at 195.2 million pounds — vs. the 2011 period.

Small-engine machines like mowers, blowers, boats and all-terrain vehicles are being hit with tougher emissions standards right along with cars and trucks, as the Environmental Protection Agency tightens federal regulations for that equipment.

In the fragmented, small-engine market, Kopinsky said, plastic fuel-tank technologies are diverse and, depending on the application, include blow molding, injection molding, thermoforming and rotational molding.

Materials used to produce those tanks include not only HDPE, but nylon and acetal.

In an Oct. 9 session on tanks at the SPE Blow Molders conference, speakers from Ticona Polymers Inc. and Lanxess Corp. discussed materials innovations for small tanks for motorcycles and small off-road engines for items like lawn and garden equipment and snowmobiles.

Ticona’s acetal copolymer, known as Hostaform S POM (polymethylene copolymer), is used in single-layer blow molded fuel tanks. Ticona modified the backbone of the polymer to make a “much more durable, much more impact-resistant material than traditional POMs,” said George Zollos, POM marketing manager for Ticona in Florence, Ky.

Hostaform S POM meets tank emissions standards, according to Zollos.

“We’re really in the early stages of introduction” to commercial markets, he said.

Maik Schulte, manager of global applications development for Lanxess Corp. in Pittsburgh, said the company’s Durethan blow molding grade of nylon, BC 550 Z XBL, meets hydrocarbon permeation standards for small engines.

He said nylon fuel tanks can also be made by rotational molding, but they can exhibit brittle behavior and require long cycle times. Monolayer blow molded nylon also is an alternative to multilayer HDPE, steel and aluminum for tanks.

Another Durethan application is in-liners for compressed natural gas tanks, Schulte said.


Comments

Stricter standards put fuel tanks under the gun

By Bill Bregar
Senior Staff Reporter

Published: November 13, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

British consumers still want their squeeze bottles when it comes to ketchup

April 16, 2014 10:02 am ET

Research commissioned by the British Plastics Federation's packaging group shows that when it comes to the nation's favorite tomato ketchup, 77...    More

Image

Austria's Greiner building a foothold in the US rigid packaging market

April 15, 2014 1:22 pm ET

Greiner Packaging International GmbH, one of Europe's largest makers of rigid plastic packaging, now wants to make its mark in the United States.    More

Fallmann named president of Consolidated Container

April 14, 2014 3:27 pm ET

Sean Fallmann, described by Consolidated Container Co. as “a seasoned packaging executive,” takes over as president and CEO of the blow...    More

Casey Container signs stock deal to help launch future production

April 10, 2014 3:34 pm ET

Casey Container Corp. continues to try to build on its plan to offer biodegradable plastic containers, announcing that it has signed a $10 million...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report provides analysis and discussions of economic and political conditions, market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as strategies being implemented by thermoformed packaging companies. In addition, there are reviews of 25 leading thermoformers in the packaging segment, assessing their growth initiatives and performance metrics over 10 years.

Learn more

Automotive Market Review and Outlook 2014 The Americas

This 75-page report features in-depth analysis of the automotive industry for the Americas. It includes discussions of market trends, legislative/regulatory activity impacting production and threats as well as design strategies being implemented by the major automakers. Detailed charts and data tables outline North American automotive production over the last five years.

Learn more

Plastics Building & Construction Market Review and Outlook 2014 with MS Excel chart data

This report provides in-depth analysis of the plastic building and construction market for North America, including discussions of trends, opportunities, threats and the latest developments in construction trends that impact plastics processors.

Learn more

Upcoming Plastics News Events

May 6, 2014 - May 8, 2014Plastics in Medical Devices 2014

May 12, 2014 - May 12, 2014Plastics News Brazil Pharma Summit

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

February 3, 2015 - February 7, 2015Plastics News Executive Forum 2015

More Events