Stricter standards put fuel tanks under the gun

By Bill Bregar
Senior Staff Reporter

Published: November 13, 2012 6:00 am ET

Related to this story

Topics Blow Molding

PITTSBURGH (Nov. 13, 2:55 p.m. ET) — It took the automotive industry about five years to develop multilayer fuel tanks that could meet California’s LEV II (low-emission vehicle) regulations in the late 1990s, said Mohammad Usman, who leads the computer-aided engineering and material department of Ford Motor Co.’s Powertrain Installations Division.

Stringent emissions standards — for cars and non-automotive small-engine equipment alike — and the transition to hybrid vehicles are some of the challenges facing carmakers and their suppliers today.

And even more-aggressive rules are coming, said Ford’s Usman. The California Air Resources Board is currently working on LEV III, to be phased in over model years 2015 through 2025.

“I’m pretty sure that this requirement that’s coming for the next 10 years is going to be much harder,” Usman said in a presentation last month at the Society of Plastics Engineers’ Blow Molding Conference in Pittsburgh.

Fuel-tank graphicHydrocarbon vapors must be fully contained in a fuel system that is entirely airtight, including the filler pipe, fuel lines and gas tanks, he said. “We want to contain everything in the system and then use it when we drive.”

The move to hybrid vehicles is also “challenging plastic fuel tanks in terms of performance requirements and the need to package batteries and tanks under the vehicle,” said Joel Kopinsky, managing director of ITB Group Ltd., a Novi, Mich.-based consulting company that tracks the global fuel-system business.

In North America, Europe and Japan, virtually all of the automotive plastic fuel tanks are extrusion blow molded, according to ITB. In North America, tanks are six layers and primarily made from high density polyethylene with an ethylene vinyl alcohol layer. In 2012, ITB projects that about 13.3 million North American vehicles will have been outfitted with HDPE tanks, Kopinsky said in a Nov. 8 email.

Washington-based American Chemistry Council data shows U.S./Canadian HDPE resin sales for blow molded auto fuel tanks up 15.7 percent for the first nine months of this year— at 195.2 million pounds — vs. the 2011 period.

Small-engine machines like mowers, blowers, boats and all-terrain vehicles are being hit with tougher emissions standards right along with cars and trucks, as the Environmental Protection Agency tightens federal regulations for that equipment.

In the fragmented, small-engine market, Kopinsky said, plastic fuel-tank technologies are diverse and, depending on the application, include blow molding, injection molding, thermoforming and rotational molding.

Materials used to produce those tanks include not only HDPE, but nylon and acetal.

In an Oct. 9 session on tanks at the SPE Blow Molders conference, speakers from Ticona Polymers Inc. and Lanxess Corp. discussed materials innovations for small tanks for motorcycles and small off-road engines for items like lawn and garden equipment and snowmobiles.

Ticona’s acetal copolymer, known as Hostaform S POM (polymethylene copolymer), is used in single-layer blow molded fuel tanks. Ticona modified the backbone of the polymer to make a “much more durable, much more impact-resistant material than traditional POMs,” said George Zollos, POM marketing manager for Ticona in Florence, Ky.

Hostaform S POM meets tank emissions standards, according to Zollos.

“We’re really in the early stages of introduction” to commercial markets, he said.

Maik Schulte, manager of global applications development for Lanxess Corp. in Pittsburgh, said the company’s Durethan blow molding grade of nylon, BC 550 Z XBL, meets hydrocarbon permeation standards for small engines.

He said nylon fuel tanks can also be made by rotational molding, but they can exhibit brittle behavior and require long cycle times. Monolayer blow molded nylon also is an alternative to multilayer HDPE, steel and aluminum for tanks.

Another Durethan application is in-liners for compressed natural gas tanks, Schulte said.


Comments

Stricter standards put fuel tanks under the gun

By Bill Bregar
Senior Staff Reporter

Published: November 13, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

African equity fund invests in Kenya's General Plastics

January 28, 2015 4:24 pm ET

An African investment fund specializing in agriculture has invested in Kenyan packaging firm General Plastics Ltd. to provide funds to expand in the...    More

Image

Bain buying TI Automotive

January 27, 2015 8:49 am ET

After months of speculation, Auburn Hills, Mich.-based TI Automotive Ltd. entered into an agreement Tuesday to be acquired by private equity firm...    More

Image

Esterform buys Constar UK, doubles PET preform capacity

January 23, 2015 10:07 am ET

Constar UK, once part of global packaging firm Constar International Holdings LLC, has a new owner.    More

Image

Canada's ABC Group to launch Polish car parts plant

January 19, 2015 9:10 am ET

Canadian auto parts supplier ABC Group Inc. has unveiled plans to set up a new production facility in Bydgoszcz, in northwestern Poland, reports...    More

Image

Temp worker disabled in accident at bottle plant

January 19, 2015 6:00 am ET

HIGH SPRINGS, FLA. — Ice River Springs Water Co. Inc., a water bottling plant in Florida, was fined $84,000 by the U.S. Occupational Safety and ...    More

Market Reports

Plastics in Automotive: Innovation & Emerging Trends

This special report newly released by PN and sponsored by The Conair Group examines current trends in the use of plastics in automotive, materials innovations and the changing landscape. It includes a review of legislative/regulatory activity impacting vehicle development and lightweighting, market opportunities & challenges for mold and toolmakers, innovative design strategies being implemented by major OEMs and suppliers, as well as a review of key indicators in Canada, Mexico, Brazil and China.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Upcoming Plastics News Events

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events