GM cars use plastics in power storage

David Vink

Published: November 19, 2012 6:00 am ET
Updated: January 3, 2013 6:30 am ET

Related to this story

Topics Automotive, Sustainability, Materials, Injection Molding, Film & Sheet, Molds/Tooling

MANNHEIM, GERMANY (Nov. 19, 12:55 p.m. ET) — The batteries in General Motors’ Opel Ampera and Chevrolet Volt electric vehicles contain more than 40 kg. of polymers.

Matthew Carroll, engineering group manager at General Motors, revealed details of the EVs’ rechargeable energy storage system (RESS) at the 2012 VDI plastics in automotive conference in Mannheim.

The RESS is made up of nine automatically assembled lithium ion 18- and 9-cell plastic battery modules, which account for 22 percent of battery system weight. These hold the battery cells in position, transfer pressure to the cells, provide heating/cooling, electric connection, cell tension sensors and integration of temperature sensors.

In each RESS, 27 kg. of polymers is used in the end frames and 135 repeater frames (made in BASF’s nylon 6/6 grade, Ultramid 1503-2F NAT, which is 33 percent glass filled and hydrolysis stabilized), the nine interconnect boards (ICBs) and the housing. Soft alignment with pins, tabs and slots are used together with brass compression limiting inserts and EPDM seals to assemble the frames into battery blocks, in preference to full snap-fit engagement.

The total amount of glass fiber reinforced nylon 6/6 used in the frames and the ICBs is 18 kg.

Yazaki North America supplies the ICB. Its manufacture involves insert molding a metal cell connector (1.4kg nylon 6 per RESS) on a vertical 300-metric ton Nissei machine. The company uses DuPont’s Zytel 7335F grade of nylon 6 for the base plate and connector housing, as well as Zytel 70G33 HS1L (35 percent glass filled nylon 6/6) for overmolding the ICB.

Mann+Hummel uses a 420-metric ton KraussMaffei electric drive injection molding machine to mold repeater and end frames in a four-cavity mold. Each cavity contains a Kistler 6157 pressure sensor to optimise control of injection pressure. Statistical analysis of injection pressures in the range 48.5-49.7 MPa over the four cavities has shown standard deviations for individual cavities of 0.38-0.40 Mpa.

M+H monitors coordinate measurement machine (CMM) values on 35 consecutive samples from each mold cavity, ensuring a maximum 0.125mm dimensional tolerance window is respected. Some parts are made on an Engel molding machine and others on a machine from a Japanese company not named in Carroll’s presentation.

Carroll said the 9.7 kg. watertight RESS housing is the heaviest part, accounting for 17 percent of battery system weight. It is molded in lightweight BD 840V vinyl ester resin based sheet molding compound (SMC) from Ashland Chemical. This contains 7 percent hadite nanoclay filler and 40 percent glass fibers that are 25mm in length.

The housing is covered in a reflective metal foil for electromagnetic shielding. The use of nanoclay filler has reduced density from 2.0 to 1.5 g/cm3 and cut 1.13kg from the part weight reduction. The coefficient of linear thermal expansion is equivalent to that of steel.

The SMC contains a styrene-based low profile additive that is acceptable so far. However, Californian AT-PZEV (Advanced Technology Partial Zero Emission Vehicle) regulations may require a switch to a styrene-free formulation in future.

Continental Structural Plastics Inc. in Huntington, Ind., supplies the silicone-sealed watertight SMC housing. The housing, which has 73 openings, is molded in an open-to-close time of 180s and an overall cycle time of 4min, allowing for cooling and flash removal. Ashland Chemical designed the mold tooling, which was made by Century Tool & Gauge in Fenton, Mich.

Another part, a 150 µm thick pouch cell, is supplied by LG Chem. Plastics account for 10 percent of its weight, with PET on the outside, polyamide coating of the gastight aluminum enclosure, a ceramic coated polyolefin SRS (safety reinforced separator) and two tie layers. There is a polyurethane foam separator between each pouch to deflect compressive forces (around 50 percent compression at 20 kPa) and their sheet metal heat exchangers are coated with a Mylar PET film layer.


Comments

GM cars use plastics in power storage

David Vink

Published: November 19, 2012 6:00 am ET
Updated: January 3, 2013 6:30 am ET

Post Your Comments


Back to story


More stories

Image

Coca-Cola sustainability report highlights PlantBottle usage

October 1, 2014 12:47 pm ET

Coca-Cola Co. has now distributed more than 25 billion PlantBottles since their introduction five years ago.    More

Image

Canadian plastics officials help with shoreline cleanup

October 1, 2014 2:35 pm ET

What's the plastics industry doing about litter? It's a good question, and given the political battles taking place around the world about product...    More

Image

OptiLedge taking Ikea's pallet replacement system to the next level

October 1, 2014 11:49 am ET

OptiLedge LLC is taking Ikea's plastic alternative to the traditional wooden pallet to the next level, making and marketing them globally.    More

Image

Houston Plastic continues to grow with new press, controlled production area

October 1, 2014 11:32 am ET

Custom injection molder Houston Plastic Products Corp. has extended its clamp tonnage range and added an environmentally controlled molding area.    More

Image

Global Plastics Summit puts PE prices in the spotlight

October 1, 2014 3:17 pm ET

Product manufacturers may start to shift away from polyethylene because of high prices, according to two major plastics processors.    More

Market Reports

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our industry analysis highlights macro industry trends and micro trends faced by companies that do business in Mexico. The report also provides key industry statistics and forecasts to anticipate future industry expansion.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Injection Molders Market Report & Ranking 2014

This special package contains our 132-page 2014 Market Report on the Injection Molding segment and our exclusive 2014 RANKINGS database of 500+ Injection Molders for a discounted package price.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events