GM cars use plastics in power storage

David Vink

Published: November 19, 2012 6:00 am ET
Updated: January 3, 2013 6:30 am ET

Related to this story

Topics Materials, Sustainability, Automotive, Film & Sheet, Injection Molding, Molds/Tooling

MANNHEIM, GERMANY (Nov. 19, 12:55 p.m. ET) — The batteries in General Motors’ Opel Ampera and Chevrolet Volt electric vehicles contain more than 40 kg. of polymers.

Matthew Carroll, engineering group manager at General Motors, revealed details of the EVs’ rechargeable energy storage system (RESS) at the 2012 VDI plastics in automotive conference in Mannheim.

The RESS is made up of nine automatically assembled lithium ion 18- and 9-cell plastic battery modules, which account for 22 percent of battery system weight. These hold the battery cells in position, transfer pressure to the cells, provide heating/cooling, electric connection, cell tension sensors and integration of temperature sensors.

In each RESS, 27 kg. of polymers is used in the end frames and 135 repeater frames (made in BASF’s nylon 6/6 grade, Ultramid 1503-2F NAT, which is 33 percent glass filled and hydrolysis stabilized), the nine interconnect boards (ICBs) and the housing. Soft alignment with pins, tabs and slots are used together with brass compression limiting inserts and EPDM seals to assemble the frames into battery blocks, in preference to full snap-fit engagement.

The total amount of glass fiber reinforced nylon 6/6 used in the frames and the ICBs is 18 kg.

Yazaki North America supplies the ICB. Its manufacture involves insert molding a metal cell connector (1.4kg nylon 6 per RESS) on a vertical 300-metric ton Nissei machine. The company uses DuPont’s Zytel 7335F grade of nylon 6 for the base plate and connector housing, as well as Zytel 70G33 HS1L (35 percent glass filled nylon 6/6) for overmolding the ICB.

Mann+Hummel uses a 420-metric ton KraussMaffei electric drive injection molding machine to mold repeater and end frames in a four-cavity mold. Each cavity contains a Kistler 6157 pressure sensor to optimise control of injection pressure. Statistical analysis of injection pressures in the range 48.5-49.7 MPa over the four cavities has shown standard deviations for individual cavities of 0.38-0.40 Mpa.

M+H monitors coordinate measurement machine (CMM) values on 35 consecutive samples from each mold cavity, ensuring a maximum 0.125mm dimensional tolerance window is respected. Some parts are made on an Engel molding machine and others on a machine from a Japanese company not named in Carroll’s presentation.

Carroll said the 9.7 kg. watertight RESS housing is the heaviest part, accounting for 17 percent of battery system weight. It is molded in lightweight BD 840V vinyl ester resin based sheet molding compound (SMC) from Ashland Chemical. This contains 7 percent hadite nanoclay filler and 40 percent glass fibers that are 25mm in length.

The housing is covered in a reflective metal foil for electromagnetic shielding. The use of nanoclay filler has reduced density from 2.0 to 1.5 g/cm3 and cut 1.13kg from the part weight reduction. The coefficient of linear thermal expansion is equivalent to that of steel.

The SMC contains a styrene-based low profile additive that is acceptable so far. However, Californian AT-PZEV (Advanced Technology Partial Zero Emission Vehicle) regulations may require a switch to a styrene-free formulation in future.

Continental Structural Plastics Inc. in Huntington, Ind., supplies the silicone-sealed watertight SMC housing. The housing, which has 73 openings, is molded in an open-to-close time of 180s and an overall cycle time of 4min, allowing for cooling and flash removal. Ashland Chemical designed the mold tooling, which was made by Century Tool & Gauge in Fenton, Mich.

Another part, a 150 µm thick pouch cell, is supplied by LG Chem. Plastics account for 10 percent of its weight, with PET on the outside, polyamide coating of the gastight aluminum enclosure, a ceramic coated polyolefin SRS (safety reinforced separator) and two tie layers. There is a polyurethane foam separator between each pouch to deflect compressive forces (around 50 percent compression at 20 kPa) and their sheet metal heat exchangers are coated with a Mylar PET film layer.


Comments

GM cars use plastics in power storage

David Vink

Published: November 19, 2012 6:00 am ET
Updated: January 3, 2013 6:30 am ET

Post Your Comments


Back to story


More stories

Image

Inteplast expands in corrugated sheet with Coroplast deal

August 21, 2014 5:28 pm ET

Packaging major Inteplast Group has acquired its main competitor in corrugated plastic sheet, Coroplast Inc. Inteplast gets corrugated sheet plants...    More

Image

Non-recyclable items gumming up the works at recycling centers

August 21, 2014 3:46 pm ET

The influx of all sorts of unacceptable items at recycling centers has gotten to the point that Charlotte, N.C.-based ReCommunity is trying to bring...    More

Image

NanoHolding, Applied Nanotech merge to form PEN Inc.

August 21, 2014 4:44 pm ET

Nanotechnology firms NanoHolding Inc. and Applied Nanotech Holdings Inc. are merging to create PEN Inc., a publicly held firm whose product mix will...    More

Image

Investment firm specializes in emerging polymer firms in Ohio

August 21, 2014 3:20 pm ET

A plastics market veteran is working with an investment firm and a research foundation to help commercialize polymer technology in the Buckeye State.    More

Image

Bayer, SCAC partner on water reuse project

August 21, 2014 12:48 pm ET

Bayer MaterialScience (BMS) and Shanghai Chlor-Alkali Chemical Co. Ltd. (SCAC) have entered into a preliminary agreement for the reuse of waste water ...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events