Dolphin process on display in truck

David Vink

Published: November 21, 2012 6:00 am ET

Italy’s Sole SpA uses the Dolphin process for the cockpit of the Mercedes-Benz Acros truck. (Daimler AG photo)

Related to this story

Topics Materials, Suppliers, Automotive

ODERZO, ITALY (Nov. 14) — In June 2011, Daimler AG’s Mercedes-Benz business launched the latest version of its Actros truck, which it said was “developed from scratch,” with a new interior design including a soft-touch cockpit.

The cockpit is injection molded using the Dolphin process, which combines foamed-in-place technology with two-component hard/soft molding. It is produced in a plant in W"rth, Germany, located on Daimler premises but operated by Italian automotive molding company Sole SpA.

Sole makes cockpit parts using Engel Coinmelt decompression technology. Dolphin was developed by Engel with Swiss mold maker Georg Kaufmann and materials suppliers BASF AG and P Group (now So.F.Ter) in 2007, based on the use of BASF’s Ultradur polybutylene terephthalate for the primary rigid component and thermoplastic elastomer from P Group.

But Sole business-development director Giuseppe Maiarellei told European Plastics News at the company’s headquarters in Oderzo, where the cockpit was displayed in its showroom, that the material solution has now changed from the original concept.

So.F.Ter supplies Pibiflex 3567 S (a TPE block copolymer from crystalline PBT and amorphous polyether glycol), and the rigid component material, a mineral-filled PC/ABS blend called Reblend.

The Dolphin process was first evaluated in 2007 by automotive supplier IAC for part of a Scania truck dashboard, and the process was shown by Engel and its Dolphin partners at K2007 in cooperation with Johnson Controls Inc. But the Actros cockpit is believed to be the first Dolphin application in serial production.

So.F.Ter said the Actros dashboard is made up of four panels extending across its entire width, including a lower part with foldaway drawers.

As with the original concept, the soft TPE secondary component is foamed using Trexel’s MuCell microcellular foaming process.

Dolphin consortium partners are talking of the potential to also physically foam the rigid component to save more weight than already achieved with the TPE surface. There should also be the possibility of using Pibiflex TPE for airbag cladding, where it maintains breakthrough performance over a wide range of temperatures, according to So.F.Ter.

Mathias Dettinger of Daimler’s interior and system evaluation department in Stuttgart said trucks and cars have been shifting toward very similar interior designs. High-quality appearance and feel of cockpits are now equally important in both sectors and are appreciated by truck drivers, who use their cabins around-the-clock as working, living and sleeping spaces.

The preceding design of the Actros 2 truck in 2002 considerably narrowed the design gap with cars; the 2011 design even more so, and this helped the new Actros win the Truck of the Year 2012 award. Mercedes-Benz offers the truck with a cockpit in two widths and three equipment lines.

Dettinger compared the cockpit made with the Dolphin process with those made with conventional back-foamed foil and cladding with foamed foils. He noted that foil thermoforming and cladding processes can cause differences in surface appearance and require wider part tolerances, leading to uneven gap dimensions.

Dettinger concluded that the other processes “are not forward-looking technologies.”

He said Dolphin, on the other hand, can achieve closer tolerances and should cost less over the product life cycle, despite “very complex and expensive tooling.”

Even if parts are designed with many reinforcement ribs in the rigid primary component, any consequent sink marks on the top surface are hidden by the foamed TPE. Integrated clips and snap fittings can be produced without sliders and designed in the same full thickness as the rest of the part, instead of being joined by a narrow section as would be needed with conventional injection molded polypropylene parts.

That aspect was well-illustrated during an Engel Symposium open house in Austria in June, where the Dolphin process was demonstrated live.

 When the new Actros application was announced in December 2011, other series applications for Dolphin were said to be under discussion. At the Engel Symposium in June, a demonstration example was displayed of a Hyundai Mobis car dashboard made with the Dolphin process, showing its applicability in cars as well as trucks.


Comments

Dolphin process on display in truck

David Vink

Published: November 21, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Delphi buying connector maker Antaya

September 22, 2014 2:25 pm ET

Delphi Automotive plc will buy Antaya Technologies Corp., a Rhode Island company that supplies wire harnesses and other technologies that connect...    More

Image

Poland's Boryszew to work with Mitsui on lightweight auto parts

September 22, 2014 10:12 am ET

European plastics car parts maker Boryszew Group has signed a letter of intent to work with the Japanese investment and trading conglomerate Mitsui & ...    More

Image

Plasan investing in capacity, jobs to supply auto market with carbon fiber

September 19, 2014 3:05 pm ET

Growth in the emerging automotive market for carbon-fiber composites has spurred a $29 million investment in a Walker, Mich., factory    More

Image

Hong Kong's TK eyes expansion, may buy Nypro Tool operation

September 19, 2014 2:49 pm ET

Hong Kong-based mold maker and plastics processor TK Group (Holdings) Ltd. said it's reached a tentative agreement to buy a tooling factory in...    More

Image

Toyoda Gosei expanding in Mexico

September 19, 2014 2:33 pm ET

Toyoda Gosei North America Corp. is investing $67 million in a 398,000-square-foot plant in central Mexico to supply the automotive industry with plas...    More

Market Reports

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Thermoformed Packaging 2014 Market Review & Outlook – North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events