Tooling pioneer DeRocher dead at 93

Published: November 28, 2012 6:00 am ET

Related to this story

Topics Injection Molding, Molds/Tooling

CHAGRIN FALLS, OHIO (Nov. 28, 3:40 p.m. ET) — Henry DeRocher, a pioneer in injection tooling who founded his own molding company at age 60, died Nov. 21 at age 93.

Born in Parker, Pa., DeRocher trained in metallurgical engineering at the Carnegie Institute of Technology before moving to Cleveland to develop plastic injection molds. He eventually founded Automation Plastics Corp., an injection molder in Aurora, Ohio, in 1980.

After college, DeRocher did research for the U.S. Navy to develop nylon rotating bands to reduce barrel wear on large battleship guns. For his research, he visited Nylon Molded Products (Nymold) in Ohio, which made prototype parts for the project.

DeRocher joined the firm in 1953, working at plants in Bedford Heights and Garrettsville, Ohio. At Nymold he worked closely with another pioneering plastics molder, Robert Hoffer Sr., who later founded Hoffer Plastics Corp. in South Elgin, Ill.

Nymold developed more than 1,000 molds during DeRocher’s tenure, according to Harry Smith, who later served as DeRocher’s general manager at Automation Plastics. Smith bought the company from DeRocher in 1999, and now serves as president.

“When Henry began Automation Plastics in 1980, at the age of 60, he began molding nylon battery seals for Union Carbide in 32- and 64-cavity molds. Henry developed many high-cavity molds as well as very long life molds,” Smith said.

“One of the 128 cavity aerosol molds for Seaquist ran over 40 million cycles in its lifetime,” Smith said.

DeRocher continued to keep an eye on Automation Plastics after he sold the company, even after he retired in 2004. Today the firm has more than 100 employees and molds nearly 2 billion parts per year.

“Henry’s early vision of the company was to design and build custom tooling and to mold close tolerance flash-free parts for automated assembly,” Smith said. “Having in-house mold maintenance capability has been pivotal to the company’s success.”

Smith said DeRocher was a trained engineer, but he “wore just about every hat there was to wear in a start-up business.”

“It’s been a privilege to work side by side with a pioneer of the injection molding industry. Both his technical genius and business acumen have been nothing short of remarkable,” Smith said. “He always enjoyed the challenge presented by developing the next generation mold design for his customers, but in his later years, perhaps he enjoyed even more, developing the next generation of people to continue the business he created.”

DeRocher is survived by his son Ben and daughter Josephine.

A memorial service will be held at the Federated Church in Chagrin Falls on Saturday, Dec. 1 at 2 p.m.


Comments

Tooling pioneer DeRocher dead at 93

Published: November 28, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Ford's final ACH plant, injection molder of HVAC systems, to close

October 22, 2014 1:58 pm ET

Ford Motor Co. will shed the last line of business in 9-year-old Automotive Component Holdings LLC by December when ACH closes its Plymouth, Mich.,...    More

Image

Comar merging with Convergence Packaging

October 21, 2014 5:07 pm ET

A couple of plastic packaging companies owned by private investment firm Graham Partners are merging into a single entity.    More

Image

Report: Suspected former Nazi with plastic connection collecting Social Security

October 20, 2014 3:52 pm ET

AKRON, OHIO — A one-time plastics executive in Akron is among dozens of suspected former Nazis who have been collecting U.S. Social Security...    More

Molder expands in France with new clean room

October 20, 2014 1:30 pm ET

Global Closure Systems (GCS), a global injection molding producer, showed off its new ISO 7 clean room at its Astra Plastique factory in France...    More

Molder goes to auction block

October 17, 2014 12:17 pm ET

An Illinois custom injection molding operation will be auctioned off after its owner decided to close the business.    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events