OSHA cites Dover Chemical

Miles Moore

Published: November 30, 2012 6:00 am ET

Related to this story

Topics Materials, Public Policy, Suppliers

DOVER, OHIO (Nov. 30, 1:35 p.m. ET) — The Occupational Safety and Health Administration has issued citations against Dover Chemical Corp. for 47 alleged violations of federal health and safety regulations.

OSHA has proposed $545,000 in fines against Dover Chemical, a manufacturer of various antioxidants, flame retardants, dispersing agents and other chemicals for the rubber and plastics industries.

The Nov. 28 citations are the result of an OSHA investigation of Dover Chemical’s manufacturing plant in Dover, involving the breach of a PVC piping system, the agency said. OSHA said it found multiple problems with the plant’s standards for process safety management, which are required of every facility that uses hazardous chemicals.

OSHA designated four of the violations as “willful,” meaning that management either deliberately disregarded federal regulations or was plainly indifferent to worker safety and health.

These violations were failure to correct deficiencies found in compliance audits; not resolving recommendations made during a process hazard analysis; having operating procedures that did not include the consequences for deviating from procedures or the steps necessary to correct deviations; and process safety information that did not detail the construction materials for piping and piping system components.

Of the remaining 43 violations, OSHA designated 41 as “serious” and two as “other than serious.” These included inaccurate operating procedures; inadequate information about the hazards of inadvertently mixing different chemicals; and lack of employee training about process safety management.

OSHA said it placed Dover Chemical in the agency’s Severe Violator Enforcement Program, which mandates targeted follow-up inspections to ensure compliance with the law.

Dover Chemical had 15 days from Nov. 28 to decide whether to comply with the OSHA order, request an informal conference with the agency’s area director or contest the citations before the independent Occupational Safety and Health Review Commission.

Dover Chemical President Dwain S. Colvin could not be reached for comment.


Comments

OSHA cites Dover Chemical

Miles Moore

Published: November 30, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

DC banning PS foam containers

July 30, 2014 2:34 pm ET

Washington D.C. Mayor Vincent Gray signed into law on July 29 a bill that will ban polystyrene foam food and drink containers from the District.    More

Image

UMass Lowell hosts collaborative research meeting for future projects

July 30, 2014 11:54 am ET

The University of Massachusetts at Lowell recently hosted a seminar, which was billed as a collaborative research meeting between Dow Chemical Co.,...    More

Image

North American robot sales set record

July 30, 2014 4:46 pm ET

The North American robotics sector is off to its fastest start ever, shattering last year's first-half record, with a first-half 2014 of 14,135...    More

Image

Pressure is on to replace aging gas pipes

July 30, 2014 2:47 pm ET

Polyethylene is the plastic replacement material of choice for modernizing the natural gas distribution system — so much so some are concerned...    More

Image

Styrolution will open new production late 2014

July 30, 2014 12:54 pm ET

Germany-based styrenic materials group, Styrolution, has announced it is expanding its facility in Ludwigshafen, Germany.    More

Market Reports

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events