Ohio puts spotlight on additive manufacturing

By Angie DeRosa
Conference Director

Published: December 7, 2012 6:00 am ET

Related to this story

Topics Public Policy Design
Companies & Associations

AKRON, OHIO (Dec. 7, 12 p.m. ET) — Additive manufacturing is in the spotlight in Northeast Ohio as the National Additive Manufacturing Innovation Institute (NAMII) is calling for proposals that are due by Jan. 31.

Additive manufacturing, also known as 3D printing or rapid prototyping, is receiving attention since NAMII was established in Youngstown, Ohio, in August, backed by $70 million in funding. The government contributed $30 million and industry contributed $40 million.

It is a pilot institute operating under the National Center for Defense Manufacturing and Machining (NCDMM).

On Dec. 3, the group held an Additive Manufacturing Seminar at the University of Akron to get industry prepared to build teams and get proposals submitted for applied research projects. The overall goal is to get a proposal accepted that would possess full manufacturing capability. The challenge is to get the technology to a place where large industrial companies can feel comfortable using it.

“We are a national institute with regional flair,” said Lisa Camp, assistant dean of strategic initiatives at Case Western Reserve University’s school of engineering in Cleveland. “We’re looking at teams and asking how do we come together? What does the supply chain look like? Could this [region] become a hotbed for this topic?”

Additive manufacturing is used in the plastics industry for prototyping and low-volume production, but often is viewed as expensive.

The goal of NAMII is to utilize the regional resources throughout northeast Ohio, western Pennsylvania and northern West Virginia to make the technology transition.

Timken Co. of Canton, Ohio, for example, has been exploring the viability of the technology. For example, officials there could look toward 3D printing as an alternative to injection molding for low volume production, said Praveen Pauskar, a technologist at Timken.

For proposals, the lead proposer must be a NAMII member and the proposal team must share at least 50 percent of the cost. The proposal team must include at least one industry organization. The full RFP can be downloaded from this site.


Comments

Ohio puts spotlight on additive manufacturing

By Angie DeRosa
Conference Director

Published: December 7, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Congress makes another attempt to update chemical regulations

April 15, 2015 11:09 am ET

A new Congress means taking yet another crack at updating the 1970s law regulating U.S. chemical manufacturing, transportation and use.    More

Image

GN Thermoforming changes management following founder's arrest

April 15, 2015 4:47 pm ET

GN Thermoforming Equipment officials say Georg Nemeskeri has stepped away from active involvement with the company he founded 34 years ago and a...    More

Image

OSHA targets firm making plastic balls used in fracking

April 15, 2015 4:55 pm ET

The U.S. Occupational Safety and Health Administration announced that it may fine a manufacturing company in New York for 48 alleged violations of...    More

Image

Economic déjà vu: strong spring growth expected after a rough winter

April 15, 2015 2:03 pm ET

The long, harsh winter is finally over, and the first quarter of the calendar is history. So now is an appropriate time to review the emerging trends ...    More

Image

Arizona bans bag bans, mandatory recycling

April 15, 2015 11:52 am ET

Swimming against the stream of bag bans around the country, a new Arizona law prohibits local bans, taxes or fees on plastic bags and other containers...    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 15, 2015 - September 17, 2015Plastics Caps & Closures - September 2015

More Events