China’s Meiling using vacuum-assisted foam injection

Published: December 18, 2012 6:00 am ET

Related to this story

Topics Machinery

HEFEI, CHINA (Dec. 18, 11:50 a.m. ET) — Appliance maker Heifei Meiling Co. Ltd. is now in full production with its innovative refrigerators made using Cannon’s vacuum-assisted injection of rigid polyurethane foam insulation.

Use of an innovative foam-filling technology – based on the use of vacuum in the cabinet during injection of polyurethane – allows for a superior distribution of foam within a refrigerator body characterized by a complex design and wide dimensions. This advantage, in combination with a special formulation developed by Dow Europe – commercially available under the Pascal brand – provides superior insulating properties to the foam, granting for an A++ energy saving classification.

Meiling is currently producing its newest models of low-consumption high-style domestic refrigerators in a new foaming plant supplied by Cannon and commissioned in September 2012.

Cannon’s foaming plant for Meiling has eight foaming fixtures, specially designed for the VAI technology, fed by one Cannon A200 Penta Twin high-pressure dosing unit through two new Cannon FPL 26 SR mixing heads.

A premixing station allows the precise metering of cyclopentane blowing agent into the polyol. Ancillary elements (pre-heating ovens for the cabinets, handling systems for empty and foam-filled units, vacuum pumps to lower the pressure within the foaming fixtures, safety systems and electronic controls) were all supplied by Cannon in a turnkey package able to make one fridge every 30 seconds.

The doors are also made with Cannon Drum units, able to produce two doors at each opening cycle of the rotary mold carriers. Here, foaming is done with open-mold pouring, making use of another high-pressure Cannon A100 dispensing unit and two Cannon FPL 18 mixing heads.

As a supplement to the new 8-fixtures plant for vacuum-assisted technology, another set of 12 conventional foaming fixtures, with all relevant “wet side” was installed in the same factory at the same time.


Comments

China’s Meiling using vacuum-assisted foam injection

Published: December 18, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Asia continues driving sales for Engel

October 21, 2014 2:42 pm ET

The number seven seems to be special for European plastics machinery makers at the moment — injection press giant Engel Holding GmbH said Oct....    More

Image

Trexel charges patent infringement against Taiwan company

October 20, 2014 3:25 pm ET

Trexel Inc., the supplier of the MuCell microcellular foaming technology, is accusing a Taiwanese company, Chuan Lih Fa Machinery Works, of violating ...    More

Image

Humanoid robot provides inspection service with a smile

October 17, 2014 6:00 am ET

Everyone knows robots can improve production and quality. But no one says they can't show a little personality while they're working.    More

Image

Arburg starts taking orders for Freeformer

October 15, 2014 12:52 pm ET

FRIEDRICHSHAFEN, GERMANY — For fans of 3-D printing, Fakuma 2014 marks an important date: Arburg is taking German orders for the Freeformer.    More

Image

Taiwan's machinery makers look to speed development of all-electrics

October 15, 2014 11:25 am ET

Taiwan's large plastics machinery industry faces a challenge — less than 10 percent of its equipment uses the more eco-friendly all-electric tec...    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events