China’s Meiling using vacuum-assisted foam injection

Published: December 18, 2012 6:00 am ET

Related to this story

Topics Machinery

HEFEI, CHINA (Dec. 18, 11:50 a.m. ET) — Appliance maker Heifei Meiling Co. Ltd. is now in full production with its innovative refrigerators made using Cannon’s vacuum-assisted injection of rigid polyurethane foam insulation.

Use of an innovative foam-filling technology – based on the use of vacuum in the cabinet during injection of polyurethane – allows for a superior distribution of foam within a refrigerator body characterized by a complex design and wide dimensions. This advantage, in combination with a special formulation developed by Dow Europe – commercially available under the Pascal brand – provides superior insulating properties to the foam, granting for an A++ energy saving classification.

Meiling is currently producing its newest models of low-consumption high-style domestic refrigerators in a new foaming plant supplied by Cannon and commissioned in September 2012.

Cannon’s foaming plant for Meiling has eight foaming fixtures, specially designed for the VAI technology, fed by one Cannon A200 Penta Twin high-pressure dosing unit through two new Cannon FPL 26 SR mixing heads.

A premixing station allows the precise metering of cyclopentane blowing agent into the polyol. Ancillary elements (pre-heating ovens for the cabinets, handling systems for empty and foam-filled units, vacuum pumps to lower the pressure within the foaming fixtures, safety systems and electronic controls) were all supplied by Cannon in a turnkey package able to make one fridge every 30 seconds.

The doors are also made with Cannon Drum units, able to produce two doors at each opening cycle of the rotary mold carriers. Here, foaming is done with open-mold pouring, making use of another high-pressure Cannon A100 dispensing unit and two Cannon FPL 18 mixing heads.

As a supplement to the new 8-fixtures plant for vacuum-assisted technology, another set of 12 conventional foaming fixtures, with all relevant “wet side” was installed in the same factory at the same time.


Comments

China’s Meiling using vacuum-assisted foam injection

Published: December 18, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Audacious vandal stuns Taipei Plas

September 29, 2014 4:59 pm ET

Melodrama erupted at the traditionally tranquil Taipei Plas trade show on Sept. 28 when a mysterious intruder flung red paint at the Baumüller...    More

Image

Shini pushes into western China

September 29, 2014 4:28 pm ET

Despite intellectual-property brigands, Taiwan's Shini Plastics Technologies Inc. is zestfully pursuing the enormous Chinese market for plastics...    More

Image

Global giant Foxconn to make, sell molding machines

September 26, 2014 2:48 pm ET

For years, Taiwan's Foxconn Technology Group has been the world's largest contract manufacturer for electronics, with more than 1 million employees...    More

Plastics Machinery Group now offering injection presses

September 26, 2014 10:46 am ET

Solon, Ohio-based Plastics Machinery Group is expanding its machinery offerings by adding injection molding machines to its inventory and adding a...    More

Image

Swiss thermoforming machinery firm WM Wrapping setting up US office

September 25, 2014 2:21 pm ET

Thermoforming industry veteran Kent Johansson has a new gig: Running a U.S. facility for Swiss sheet line and thermoforming machinery maker WM Wrappin...    More

Market Reports

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our industry analysis highlights macro industry trends and micro trends faced by companies that do business in Mexico. The report also provides key industry statistics and forecasts to anticipate future industry expansion.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Injection Molders Market Report & Ranking 2014

This special package contains our 132-page 2014 Market Report on the Injection Molding segment and our exclusive 2014 RANKINGS database of 500+ Injection Molders for a discounted package price.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events