Arburg spotlights consistency, quality control, speed at seminar

By Bill Bregar
Senior Staff Reporter

Published: December 20, 2012 6:00 am ET

Visitors check out one of Arburg’s all-electric injection presses during the firm’s technical seminar in Elgin, Ill. (Plastics News photo by Bill Bregar)

Related to this story

Topics Machinery

Neff, who works out of the Elgin facility, also outlined machinery drive technology, from hydraulic to hybrid to all-electric. There is no single best solution, he said: “You need to look at your part family before you decide.”

Arburg can build modular machines, where the customer chooses which type of power to run each function.

Arburg ran two all-electric injection presses at the seminar. An Allrounder Edrive, with 110 tons of clamping force, molded medical syringe barrels on an eight-second cycle using an edge-gated Heitec hot runner. Arburg has positioned the Edrive as an entry-level all-electric.

The other press, a 110-ton Alldrive, was molding medical fittings from liquid silicone rubber, using an Elmet mold and LSR dosing system. Cycle time for the four-cavity mold: 28 seconds.

Susan Montgomery, president of Priamus System Technologies LLC, detailed the Brunswick, Ohio, company’s Fillcontrol platform that makes sure the mold is completely filled with plastic, and the related BlueLine hardware. Fillcontrol is a new modular concept with four modules, using mold-cavity pressure and temperature sensors to measure viscosity, fill time, shear stress of the melt, and part compression and shrinkage.

One key function is to detect the melt front from the mold-fill stage to pack and hold. The system also can do sequential control of valve gates.

“The nice thing about these systems is they are machine-independent,” Montgomery said, adding that this means Fillcontrol can be used on presses in far-flung global factories. “We are looking at long-term part consistency,” she said.

John Bozzelli delivered a rousing, riff-laden talk on making identical parts out of multicavity molds. He got into how plastic flows, as the polymer molecules slide past each other under pressure from the press. Viscosity is very much impacted by shear rate, he said, and that means changing pressure — not temperature — is the way to change viscosity.

Bozzelli is CEO of Injection Molding Solutions in Midland, Mich.

Arburg seminar attendees got a grounding in multishot turning-cube molds from David Nolan, North American sales manager for German toolmaker Foboha GmbH. Cube molds can run parts with two or more materials and do in-mold assembly.

Nolan showed videos of 180-degree stack turning molds, a 90-degree turning cube and other layouts.

Because the tool has more than one mold face and injection units, you can pump out large-cavitation multicomponent parts on a smaller press than would normally be needed.

“There’s some incredible potential for volumes with this process,” he said.

Hot runners  

On the hot-runner front, smaller sizes, engineering resins and difficult gate locations are a challenge, said Paul Boettger of Technoject Machinery Corp., which represents Heitec hot runners from Germany.

Historically, it was tough to make a hot runner to handle tiny parts of less than 5 grams, Boettger said. But now they can handle parts less than a single gram.

“These parts are becoming more and more difficult to direct gate,” he said.

That puts a challenge on hot-runner makers to develop shorter nozzles with smaller nozzle spacing. Using a flat nozzle, Heitec can do minimal nozzle spacing of 4.5 millimeters, suitable for parts that weigh less than 1 gram. He showed a slide of a mold for toothpicks.

Deciding where to locate the gate is important, to hide the gate vestige, Boettger said.


Comments

Arburg spotlights consistency, quality control, speed at seminar

By Bill Bregar
Senior Staff Reporter

Published: December 20, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

North American robot sales set record

July 30, 2014 4:46 pm ET

The North American robotics sector is off to its fastest start ever, shattering last year's first-half record, with a first-half 2014 of 14,135...    More

Image

Gear pump maker Witte expands in Germany and USA

July 25, 2014 2:15 pm ET

Witte Pumps & Technology GmbH, the German maker of gear pumps for extrusion, has moved into a new headquarters factory in the Hamburg area, and the...    More

Image

Munson Machinery expanding assembly, testing operations

July 22, 2014 2:02 pm ET

Munson Machinery Co. Inc. is expanding its headquarters factory by about one-third in Utica, N.Y., where the company makes mixing, blending and size-...    More

Image

Windmöller & Hölscher looking to continued growth in China

July 21, 2014 3:40 pm ET

With 2013 global sales of 600 million euros, China has grown into an important export market for Windmöller & Hölscher KG, second only to the United...    More

Image

Thermoforming Technology Group adds Lyle Industries to its portfolio

July 18, 2014 2:48 pm ET

Thermoforming Technology Group LLC has expanded its thermoforming equipment presence with the acquisition of Lyle Industries Inc.    More

Market Reports

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events