Faurecia's new technology adapts to existing production

By Rhoda Miel
News Editor

Published: December 27, 2012 6:00 am ET

The injection molded base below is visible below the Urban Rhythm’s foam and cover. The specially designed thermoplastic base can be engineered to move with the occupant. (Faurecia SA photo)

Related to this story

Topics Materials Suppliers Sustainability Automotive
Companies & Associations

AUBURN HILLS, MICH. (Dec. 27, 12:20 p.m. ET) — — Faurecia SA has been showing its potential weight-saving composite seating to automakers for a few years. But just in case carmakers aren’t ready to change their seats completely, the auto supplier is also showing them how to bring new seating concepts into an existing production infrastructure.

“We’re not backing off from [the composite proposal] but we’re showing them how they can take plastic and apply it to an existing structure,” said Mike Miner, product line manager for seating for Faurecia North America, during a Dec. 19 interview at Faurecia’s North American headquarters in Auburn Hills.

Faurecia showed its latest concept interiors and seating to automakers at the Los Angeles Auto Show in November.

In seating, the company is continuing to use injection molding for structural shells to support thinner and lighter seating, but its Urban Rhythm concept married them with a steel frame, rather than composite proposals shown previously on the 2011 Performance Seat concept.

While automakers need to bring down vehicle weight to meet requirements for lower fuel consumption — and seating is a big focus for potential weight savings — automakers also know that seats must pass rigorous crash requirements. That makes it harder to commit to large-scale changes in material standards.

Urban Rhythm would allow them to keep familiar structures that have passed crash tests for years, but also to trim seating weight and sizes within that structure, Miner said. The combination of steel and plastics could provide the fastest way to bring Faurecia’s concepts to the market.

The seats also build on previous Faurecia proposals by expanding the use of an injection molded shell to the seat cushion in addition to the seat back.

A typical seat cushion uses foam and springs on top of a steel base. Faurecia proposes to exchange that for a specially designed thermoplastic base that can be engineered to move with the occupant, similar to the way injection molding has been used in executive seating in the office furniture industry.

Faurecia already has worked with office furniture giant Steelcase Inc. to adapt the Steelcase Leap chair technology for seat backs for concept lightweight seats. Miner said it extended that thinking under its own engineering team to the seat cushion, with a shape designed to move along with people in a “bio-sympathetic” form.

The injection molded base would be molded with a foam-in-place cover skin for a thin profile, maxing out with 35 millimeters of foam.

Urban Rhythm is focused on smaller cars, although it could go into any size vehicle, Miner said.

Faurecia will kick off tooling development for prototype production of the seat backs in 2013. Seat cushion development is about a year from prototype tooling.

Faurecia is also looking at ways to make it easier for automakers to adapt new technology in interior trim.

The supplier has used a natural material composite in substrates for years, in parts such as door panels. It has produced the substrate in more than 60 vehicles over 20 years. Natural materials reduce weight by 25-40 percent compared with a glass-reinforced substrate, but the desire to maintain a standard appearance in interior trim prompted automakers to cover them with cloth or a skin, which brings weight back onto the part.

With its new Ligneco process, Faurecia can combine the compression molded substrate with a very thin polypropylene decorative foil, which provides a familiar surface but at a lower cost and weight, said Jay Hutchins, director of marketing and product planning.

“We’ve done a lot as an industry with development of technology,” Hutchins said. “Breakthrough technology is great, but it’s always a big step for the industry, so what can we do that will be easier for the entire industry to use?”


Comments

Faurecia's new technology adapts to existing production

By Rhoda Miel
News Editor

Published: December 27, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Resin prices remain unpredictable

April 27, 2015 12:23 pm ET

Oil prices leveled off a bit in March, but North American commodity resin prices remained as unpredictable as ever.    More

Image

Dow Chemical bullish about prospect for global polyurethane markets

April 27, 2015 11:17 am ET

MAASTRICHT, THE NETHERLANDS — Glenn Wright, president of Dow Chemical Co.’s polyurethanes and formulated systems business, revealed that...    More

Image

PolyOne launches Geon BIO PVC using soy-based materials

April 24, 2015 11:48 am ET

More than a decade of research is paying off for Battelle Memorial Institute in the form of Geon BIO PVC compounds from PolyOne Corp.    More

Image

Study suggests infants at lower risk from BPA exposure than expected

April 23, 2015 4:58 pm ET

A new study shows that newborn babies may have less risk from bisphenol A exposure than originally thought.    More

Image

Braskem and Odebrecht reconsidering West Virginia plastics project

April 23, 2015 2:54 pm ET

Brazilian firms Braskem and Odebrecht have confirmed that they are re-evaluating Project Ascent, the major plastics and petrochemicals project they ha...    More

Market Reports

North American Thermoformed Packaging Market Outlook & Review 2015

Our annual report provides a thorough review and analysis of economic and political conditions, emerging market trends, packaging design advances, materials pricing and sustainable packaging issues impacting supply and demand in the TP segment. Our analysts identify key drivers of growth and opportunities for processors to remain competitive in the years ahead through innovation, production efficiencies and more.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 15, 2015 - September 17, 2015Plastics Caps & Closures - September 2015

More Events