Faurecia's new technology adapts to existing production

By Rhoda Miel
News Editor

Published: December 27, 2012 6:00 am ET

The injection molded base below is visible below the Urban Rhythm’s foam and cover. The specially designed thermoplastic base can be engineered to move with the occupant. (Faurecia SA photo)

Related to this story

Topics Materials, Suppliers, Sustainability, Automotive

AUBURN HILLS, MICH. (Dec. 27, 12:20 p.m. ET) — — Faurecia SA has been showing its potential weight-saving composite seating to automakers for a few years. But just in case carmakers aren’t ready to change their seats completely, the auto supplier is also showing them how to bring new seating concepts into an existing production infrastructure.

“We’re not backing off from [the composite proposal] but we’re showing them how they can take plastic and apply it to an existing structure,” said Mike Miner, product line manager for seating for Faurecia North America, during a Dec. 19 interview at Faurecia’s North American headquarters in Auburn Hills.

Faurecia showed its latest concept interiors and seating to automakers at the Los Angeles Auto Show in November.

In seating, the company is continuing to use injection molding for structural shells to support thinner and lighter seating, but its Urban Rhythm concept married them with a steel frame, rather than composite proposals shown previously on the 2011 Performance Seat concept.

While automakers need to bring down vehicle weight to meet requirements for lower fuel consumption — and seating is a big focus for potential weight savings — automakers also know that seats must pass rigorous crash requirements. That makes it harder to commit to large-scale changes in material standards.

Urban Rhythm would allow them to keep familiar structures that have passed crash tests for years, but also to trim seating weight and sizes within that structure, Miner said. The combination of steel and plastics could provide the fastest way to bring Faurecia’s concepts to the market.

The seats also build on previous Faurecia proposals by expanding the use of an injection molded shell to the seat cushion in addition to the seat back.

A typical seat cushion uses foam and springs on top of a steel base. Faurecia proposes to exchange that for a specially designed thermoplastic base that can be engineered to move with the occupant, similar to the way injection molding has been used in executive seating in the office furniture industry.

Faurecia already has worked with office furniture giant Steelcase Inc. to adapt the Steelcase Leap chair technology for seat backs for concept lightweight seats. Miner said it extended that thinking under its own engineering team to the seat cushion, with a shape designed to move along with people in a “bio-sympathetic” form.

The injection molded base would be molded with a foam-in-place cover skin for a thin profile, maxing out with 35 millimeters of foam.

Urban Rhythm is focused on smaller cars, although it could go into any size vehicle, Miner said.

Faurecia will kick off tooling development for prototype production of the seat backs in 2013. Seat cushion development is about a year from prototype tooling.

Faurecia is also looking at ways to make it easier for automakers to adapt new technology in interior trim.

The supplier has used a natural material composite in substrates for years, in parts such as door panels. It has produced the substrate in more than 60 vehicles over 20 years. Natural materials reduce weight by 25-40 percent compared with a glass-reinforced substrate, but the desire to maintain a standard appearance in interior trim prompted automakers to cover them with cloth or a skin, which brings weight back onto the part.

With its new Ligneco process, Faurecia can combine the compression molded substrate with a very thin polypropylene decorative foil, which provides a familiar surface but at a lower cost and weight, said Jay Hutchins, director of marketing and product planning.

“We’ve done a lot as an industry with development of technology,” Hutchins said. “Breakthrough technology is great, but it’s always a big step for the industry, so what can we do that will be easier for the entire industry to use?”


Comments

Faurecia's new technology adapts to existing production

By Rhoda Miel
News Editor

Published: December 27, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Vinyl siding's lead slips, but industry pushing back

July 29, 2014 2:04 pm ET

Vinyl siding continues to be the top cladding choice for home builders and remodelers but fiber cement is gaining ground — at an alarming rate...    More

Unipex Group buys Ferguson Chemical Innovation

July 29, 2014 1:57 pm ET

Chemical distributor Unipex Group Inc. announced July 29 that it had purchased Ferguson Chemical Innovation, a Brampton, Ontario-based supplier of...    More

Image

Magna expanding interiors site in Slovakia

July 29, 2014 1:47 pm ET

Magna International Inc. plans to nearly double the size of its manufacturing facility in Trnava, in western Slovakia, to accommodate new automotive...    More

Image

Carbon black supplier Orion begins trading on NYSE

July 29, 2014 11:29 am ET

Orion Engineered Carbons S.a.r.l. has priced the initial public offering of 19.5 million common shares at a price to the public of $18 per share.    More

Image

Dow sees solid second quarter performance

July 29, 2014 11:19 am ET

Dow Chemical Co. has reported its second quarter figures, with its seventh consecutive quarter of growth, according to the company.
More

Market Reports

Plastics Recyclers Data Report & Directory

This exclusive MS Excel database contains all the companies from Plastics News' ranking of top North American Recyclers and Brokers by reprocessed volume and also includes a directory with materials processes, services offered and company contact information. Data is based on primary research by PN editorial staff.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events

Newsletters

Select from the list below to subscribe to customized Plastics News e-mail news alerts. Check the options you wish to receive.

View samples of all eNewsletters »

More Newsletters