Faurecia's new technology adapts to existing production

By Rhoda Miel
News Editor

Published: December 27, 2012 6:00 am ET

The injection molded base below is visible below the Urban Rhythm’s foam and cover. The specially designed thermoplastic base can be engineered to move with the occupant. (Faurecia SA photo)

Related to this story

Topics Automotive, Sustainability, Materials, Suppliers

AUBURN HILLS, MICH. (Dec. 27, 12:20 p.m. ET) — — Faurecia SA has been showing its potential weight-saving composite seating to automakers for a few years. But just in case carmakers aren’t ready to change their seats completely, the auto supplier is also showing them how to bring new seating concepts into an existing production infrastructure.

“We’re not backing off from [the composite proposal] but we’re showing them how they can take plastic and apply it to an existing structure,” said Mike Miner, product line manager for seating for Faurecia North America, during a Dec. 19 interview at Faurecia’s North American headquarters in Auburn Hills.

Faurecia showed its latest concept interiors and seating to automakers at the Los Angeles Auto Show in November.

In seating, the company is continuing to use injection molding for structural shells to support thinner and lighter seating, but its Urban Rhythm concept married them with a steel frame, rather than composite proposals shown previously on the 2011 Performance Seat concept.

While automakers need to bring down vehicle weight to meet requirements for lower fuel consumption — and seating is a big focus for potential weight savings — automakers also know that seats must pass rigorous crash requirements. That makes it harder to commit to large-scale changes in material standards.

Urban Rhythm would allow them to keep familiar structures that have passed crash tests for years, but also to trim seating weight and sizes within that structure, Miner said. The combination of steel and plastics could provide the fastest way to bring Faurecia’s concepts to the market.

The seats also build on previous Faurecia proposals by expanding the use of an injection molded shell to the seat cushion in addition to the seat back.

A typical seat cushion uses foam and springs on top of a steel base. Faurecia proposes to exchange that for a specially designed thermoplastic base that can be engineered to move with the occupant, similar to the way injection molding has been used in executive seating in the office furniture industry.

Faurecia already has worked with office furniture giant Steelcase Inc. to adapt the Steelcase Leap chair technology for seat backs for concept lightweight seats. Miner said it extended that thinking under its own engineering team to the seat cushion, with a shape designed to move along with people in a “bio-sympathetic” form.

The injection molded base would be molded with a foam-in-place cover skin for a thin profile, maxing out with 35 millimeters of foam.

Urban Rhythm is focused on smaller cars, although it could go into any size vehicle, Miner said.

Faurecia will kick off tooling development for prototype production of the seat backs in 2013. Seat cushion development is about a year from prototype tooling.

Faurecia is also looking at ways to make it easier for automakers to adapt new technology in interior trim.

The supplier has used a natural material composite in substrates for years, in parts such as door panels. It has produced the substrate in more than 60 vehicles over 20 years. Natural materials reduce weight by 25-40 percent compared with a glass-reinforced substrate, but the desire to maintain a standard appearance in interior trim prompted automakers to cover them with cloth or a skin, which brings weight back onto the part.

With its new Ligneco process, Faurecia can combine the compression molded substrate with a very thin polypropylene decorative foil, which provides a familiar surface but at a lower cost and weight, said Jay Hutchins, director of marketing and product planning.

“We’ve done a lot as an industry with development of technology,” Hutchins said. “Breakthrough technology is great, but it’s always a big step for the industry, so what can we do that will be easier for the entire industry to use?”


Comments

Faurecia's new technology adapts to existing production

By Rhoda Miel
News Editor

Published: December 27, 2012 6:00 am ET

Post Your Comments


Back to story


More stories

Image

Symphony Environmental defends biodegrade plastics in recycling stream

September 17, 2014 11:47 am ET

Symphony Environmental Technologies plc, one of the world's largest oxo-biodegradable technology companies, has responded to a leading Mexican...    More

Image

Tiny plastics swim in Australian waters

September 17, 2014 11:16 am ET

A University of Western Australia marine scientist has found the sea's surface in Australian waters is contaminated by more than 4,000 pieces of tiny ...    More

Image

Cascade Engineering founder Keller to step down as CEO

September 16, 2014 8:33 pm ET

Cascade Engineering Inc. is undergoing a transition as President Mark Miller will also add the role of CEO, replacing founder Fred Keller, who has...    More

Image

DuPont investing $100 million for more ethylene copolymer capacity

September 16, 2014 1:51 pm ET

Increased packaging demand is leading materials giant DuPont Co. to spend more than $100 million to increase capacity for ethylene copolymers at its...    More

Image

Canadian, Mexican injection molders form auto supply joint venture

September 16, 2014 2:26 pm ET

A new automotive parts manufacturer will open in Querétaro, Mexico, through a joint venture between Canadian automotive supplier Papp Plastics and Dis...    More

Market Reports

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Thermoformed Packaging 2014 Market Review & Outlook – North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events