Peninsula Plastics expanding at Ontario site

By Michael Lauzon
Correspondent

Published: January 11, 2013 6:00 am ET

Related to this story

Topics Consumer Products, Injection Molding

FORT ERIE, ONTARIO (Jan. 11, 2:30 p.m. ET) — Injection molder Peninsula Plastics Ltd. overcame bureaucratic delays and is constructing an expansion of its operation in Fort Erie, Ontario.

“We had a lot of issues with the conservation authority because a flood plain is close to our property,” said Peninsula President Craig Bolton by phone.

Another problem was Peninsula’s desire to build a 30-foot-high addition to its 20-foot-high plant. Building codes would have require costly reinforcement for the combined structure.

Instead, Peninsula opted to build a 25,000-square-foot building next to its 35,000-square-foot one and connect them.

“There was a lot of discussion about the rules that indicate what is an expansion vs. a different building,” Bolton said.

Bolton, Peninsula’s owner, said the firm intends to finish the new building in March. It has bought two injection presses and plans to buy two more for the expansion. One of the new ones will exceed 1,000 tons of clamping force — currently the biggest size among Peninsula’s 27 presses. Bolton did not reveal the cost of the expansion.

Peninsula is a custom molder for diverse industries and also does proprietary products for insect control, and makes edge protectors, spools and eyewear protection. It recently began making curbside recycling bins and expects that business to grow so much that it has set up a separate division for it.

Fort Erie Mayor Doug Martin was one of the municipal officials who convinced regional officials that Peninsula’s plan should not be held back by red tape.


Comments

Peninsula Plastics expanding at Ontario site

By Michael Lauzon
Correspondent

Published: January 11, 2013 6:00 am ET

Post Your Comments


Back to story


More stories

Molder goes to auction block

October 17, 2014 12:17 pm ET

An Illinois custom injection molding operation will be auctioned off after its owner decided to close the business.    More

Image

Plastikon expanding in Kentucky

October 17, 2014 11:24 am ET

Automotive supplier Plastikon Industries Inc. plans to more than double the size of its production facility in Leitchfield, Ky.    More

Image

Taiwan's machinery makers look to speed development of all-electrics

October 15, 2014 11:25 am ET

Taiwan's large plastics machinery industry faces a challenge — less than 10 percent of its equipment uses the more eco-friendly all-electric...    More

Image

French molder betting on growth in the auto industry, Detroit

October 14, 2014 6:00 am ET

Precision French molder AdduXi Group is opening its first factory outside of its home country — in a Detroit suburb — and the top local...    More

Image

Wright Plastic Products adding two-shot molding capabilities in St. Clair

October 10, 2014 3:23 pm ET

Michigan custom injection molder Wright Plastic Products will add two-shot molding capabilities as part of an expected $1.8 million investment in new ...    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events