Mileage-boosting tech on display at auto show

Dustin Walsh

Published: January 14, 2013 6:00 am ET

Related to this story

Topics Public Policy, Sustainability, Automotive

DETROIT (Jan. 14, 11 a.m. ET) — Cars will do what cars do at the North American International Auto Show — draw crowds and cameras.

But at several exhibits, rapid advancements in new fuel-saving products will have supplier executives and politicians using the Detroit event as a showcase for new technology and a platform to talk about the future.

While automotive infotainment was the focus at last week’s Consumer Electronics Show in Las Vegas, fuel economy technology will shine at this week’s NAIAS media and industry days at Cobo Center.

Suppliers such as Denso International America Inc. and Johnson Controls Inc. are displaying emerging fuel-saving technology at this year’s show.

Doug Patton, senior vice president of Denso International’s engineering division, said suppliers are moving toward complete systems to highlight technology, which makes them more visible than individual products.

“There’s always been a lot of technology at the auto show, but it’s been buried in the car and you didn’t see it,” Patton said. “What you’re seeing now is a system approach where we bring technologies together and look at them as a whole for the best value.”

The challenge, experts say, is how to unite these technology advancements with sales strategies for OEMs.

David Cole, chairman of nonprofit research group Auto Harvest and chairman emeritus of the Center for Automotive Research in Ann Arbor, Mich., said the increase in fuel-savings technology is a prime example of an uncertain industry.

Bottom line: The added costs of these technologies, while promoted and touted at NAIAS, may not equate to consumer adoption — at least not yet.

“We’re really pushing the laws of the thermodynamics of engine performance, but at what cost?” Cole said. “This is really expensive stuff, and nobody has the right answer to the best benefit, so everyone is kind of out there working on a lot of things.”

The government push for fuel economy is pitting increased technology against consumer pocketbooks. CAR estimates a $2,000 increased vehicle cost for a 20 percent improvement in fuel economy.

“Is that enough?” Cole said. “It’s a very confusing period for the industry.”

Government-regulated CAFE standards require manufacturers to meet a 54.5 mpg average across their fleets by 2025.

Automakers and suppliers alike continue to push these technologies and push further into vehicle electrification to appease government demands, despite ho-hum sales.

The Detroit show is expected to host various federal officials from EPA and other agencies.

Among the green cars being highlighted at the Detroit show, General Motors Co. will unveil its Cadillac ELR Luxury Electric Hybrid on Tuesday morning, Via Motors will showcase battery-electric cars and BMW will debut its ActiveHybrid3.

Experts say that for consumers, range anxiety remains the biggest stumbling block for EV adoption. The Chevy Volt, for example, achieves roughly 40 miles on its electric battery before a traditional gas-powered motor steps in.

In a KPMG LLP study released last week, 87 percent of automotive executives said EVs won’t match the range of gas-powered vehicles for at least another five years.

“Clearly, they don’t see the numbers of these vehicles increasing,” said Betsy Meter, partner at KPMG in Detroit and its automotive audit leader. “We all kept expecting these numbers to significantly increase, but executives continue to see them at a low level, despite investment.”

U.S. EV sales totaled 52,835 in 2012, according to the Electric Drive Transportation Association. The grand total of hybrids, plug-in hybrids and battery electric vehicles sold last year in the U.S. totaled 487,480, which represents 3.4 percent of the 14.5 million cars sold last year.

That’s better than the 2.2 percent of total sales in 2011. And the market for EVs is expanding alongside the growing U.S. auto market — which is expected to eclipse 15 million units this year.


Comments

Mileage-boosting tech on display at auto show

Dustin Walsh

Published: January 14, 2013 6:00 am ET

Post Your Comments


Back to story


More stories

California lawmakers give final approval to plastic bag ban

August 30, 2014 6:00 am ET

Under the measure, single-use plastic bags will be barred from California retailers, including grocery stores, convenience stores and drug stores, as ...    More

Image

Poor plastic coating prompts cable recall

August 29, 2014 2:10 pm ET

Australia's competition regulator, the Australian Competition and Consumer Commission (ACCC), has ordered a major recall of 2,485 miles of electrical ...    More

Image

EPA fines RI polymer company

August 29, 2014 1:20 pm ET

A Rhode Island polymer manufacturer has reached a $60,000 settlement with the U.S. Environmental Protection Agency (EPA) for violating federal clean...    More

Image

Green trend boosts plastic building materials business in China

August 29, 2014 9:42 am ET

The greening of China's domestic building materials market is giving the plastics industry a boost.    More

Polish injection molder Teknorubber up for sale

August 29, 2014 9:14 am ET

Polish plastic parts maker Teknorubber has been put up for sale following its insolvency filing in March 2014. The company is to be auctioned through ...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events