2014 Corvette decked out in carbon fiber

By Rhoda Miel
News Editor

Published: January 14, 2013 6:00 am ET

Related to this story

Topics Automotive, Materials, Suppliers

DETROIT (Jan. 14, 10:45 a.m. ET) — General Motors Co. is upping the ante on carbon fiber for the auto industry, making the composite standard for the hood and roof on its next-generation Chevrolet Corvette.

GM unveiled the 2014 Corvette — the seventh generation, or C7, for the sports car — during a special event Jan. 13 in advance of the North American International Auto Show in Detroit. GM has brought back the Stingray name for the new Corvette.

While the Corvette has had carbon fiber as an upgraded option in the past, the new Corvette will have it on every vehicle, even base-line models, said Tadge Juechter, the car’s chief engineer.

The carbon-fiber hood comes in at about half the weight of the current sheet-molded-compound version, said Tom Toft, body vehicle systems engineer, during an interview after the Corvette unveiling. The roof on the 2014 C7 version is slightly larger than its sixth-generation predecessor, but carbon fiber still reduces the weight to 6 kilograms, from 9 kilograms.

Dropping weight in those parts helps to lower the Corvette’s center of gravity, which improves performance, Toft noted, while the lighter roof also will be appreciated by buyers who remove the panel for drives on sunny days.

The carbon-fiber body panels will come to the assembly plant ready to be painted, just as current SMC panels arrive, he said. That will allow the automaker to bring the carbon fiber on line seamlessly.

The Corvette still is far from a mainstream car. IHS Automotive estimates GM will sell 21,000 Corvettes in 2014 — still making it a low-volume vehicle for the industry. However, production of carbon-fiber body parts even at that level will push the volume of the composite used in the industry.

The 21,000 projected sales figure for Corvette paces well above the 2,000-3,000 Chrysler Group LLC Vipers sold each year. The Viper is Corvette’s closest North American rival, and launched production with a carbon-fiber hood, roof and trunk lid in 2012.

The Viper uses a standard pre-preg process for its carbon-fiber parts, made by Plasan Carbon Composites of Bennington, Vt.

While GM has not released the name of its parts supplier for the carbon fiber on the Corvette, Toft noted that it is using a newly developed heat and pressure production process. Plasan is building an $18 million plant in Walker, Mich., to produce parts starting this year for an unnamed vehicle, using in-house-developed production with a compression press system.

“For GM, the more we can do that can make carbon fiber more affordable, and the more we can use it, the better it is for everyone,” Toft said.

In addition to the standard painted body panels, customers will also have an option to buy panels with an exposed weave. Those parts will be made in a more traditional process. However, if an exposed-weave part develops a flaw during production, the automaker can put that part back into production as a painted part, rather than scrapping the entire panel, as happens today.


Comments

2014 Corvette decked out in carbon fiber

By Rhoda Miel
News Editor

Published: January 14, 2013 6:00 am ET

Post Your Comments


Back to story


More stories

Axiall resumes operations at damaged Lake Charles PVC feedstock plant

April 15, 2014 4:41 pm ET

Axiall Corp. has resumed operations at its PVC feedstock plant that was damaged by a fire in December.
More

Image

Power failure shuts down two PE resin units in Texas

April 15, 2014 3:35 pm ET

Two polyethylene resin units operated by Chevron Phillips Chemical Co. LP in Baytown, Texas, were closed from April 8-11 because of a power failure.    More

Shell Chemical to host public meetings to discuss plans in Pennsylvania

April 15, 2014 3:27 pm ET

Shell Chemical LP will host two public meetings on April 16 to discuss the possibility of building a major petrochemicals plant in the Pittsburgh...    More

Image

Despite struggles, Europe still key market in global resin picture

April 15, 2014 2:06 pm ET

Challenges and opportunities facing international plastics and chemicals markets were tackled by a trio of top executives at the IHS World...    More

Shintech in early stages of planning ethylene feedstock plant in Louisiana

April 15, 2014 3:22 pm ET

Shintech Inc. has filed an air permit with the Louisiana Department of Environmental Quality that would allow for the construction of a new unit with ...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report provides analysis and discussions of economic and political conditions, market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as strategies being implemented by thermoformed packaging companies. In addition, there are reviews of 25 leading thermoformers in the packaging segment, assessing their growth initiatives and performance metrics over 10 years.

Learn more

Automotive Market Review and Outlook 2014 The Americas

This 75-page report features in-depth analysis of the automotive industry for the Americas. It includes discussions of market trends, legislative/regulatory activity impacting production and threats as well as design strategies being implemented by the major automakers. Detailed charts and data tables outline North American automotive production over the last five years.

Learn more

Plastics Building & Construction Market Review and Outlook 2014 with MS Excel chart data

This report provides in-depth analysis of the plastic building and construction market for North America, including discussions of trends, opportunities, threats and the latest developments in construction trends that impact plastics processors.

Learn more

Upcoming Plastics News Events

May 6, 2014 - May 8, 2014Plastics in Medical Devices 2014

May 12, 2014 - May 12, 2014Plastics News Brazil Pharma Summit

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

February 3, 2015 - February 7, 2015Plastics News Executive Forum 2015

More Events