Henniges touts ability to cut weight from seals

Allison Strouse

Published: January 15, 2013 6:00 am ET

Related to this story

Topics Sustainability Automotive Pipe/Profile/Tubing
Companies & Associations

AUBURN HILLS, MICH. (Jan. 15, 11:30 a.m. ET) — Henniges Automotive Holdings Inc. has found ways to cut anywhere from eight to 12 pounds from vehicle weight through sealing alone.

“Our product has often been overlooked in the area of weight,” CEO Douglas DelGrosso said. “People focus on typically metal and steel to get weight off and if you think about the amount of sealing that is in the typical C-Class sedan, it’s a lot of product and rubber is heavy.”

In an environment fueled by meeting such standards as fuel efficiency and emissions reductions, being able to take weight off a vehicle wherever possible helps.

“If you find some creative ways to take off weight and take it to the customer in today’s environment with all the pressure that’s on them to meet, whether its CO2 standards or general emissions standards, we have tried to focus ourself there,” he said.

DelGrosso sees this as a big opportunity for his firm if it is able to show its customers the potential for such reductions.

“That’s a pretty significant amount of savings [in weight],” he said. “That represents about a 20-percent reduction in the overall weight. ... Some of it can be done without any additional costs.”

If done on a large enough scale, he added, it might even amount to a cost savings.

Going with plastic over rubber has been the answer in the past on occasion, according to Steve Murree, Henniges director of advanced product and process development. To help reduce the mass of the products, eliminating materials like rubber and metal have helped.

While the push for this mainly is coming from Henniges, the executives said there have been a few customers coming to the auto supplier looking for a solution.

“Each customer has their traditional way of engineering sealing,” DelGrosso said. “This is where we can be that catalyst.”

Looking over what the best practices and procedures are, he said this was the firm’s chance to approach its customers and say here is the best way to accomplish weight reduction.

“We can be in that eight- to maybe 11-pound range,” DelGrosso said.

“I think that requires a certain level of push from us. Not all [car makers] are out there doing those teardowns to get that type of data [on reducing weight in sealing].”

Getting the information to their customers isn’t the hard part though.

“One of the struggles is that the working level, their objective is to launch vehicles without issues,” Murree said. While they like the push from the company, lessening the weight and coming up with alternatives for sealing are not among their main objectives.

“We have to start attacking higher up and having them push it down as an objective,” he said.

Issues like fuel efficiency are not expected to go away anytime soon.

“What we are trying to do is be ahead of that because we can, and be there as a good value supplier and say we have some ideas that you didn’t traditionally look at for this product,” DelGrosso said.


Comments

Henniges touts ability to cut weight from seals

Allison Strouse

Published: January 15, 2013 6:00 am ET

Post Your Comments


Back to story


More stories

Image

PolyOne launches Geon BIO PVC using soy-based materials

April 24, 2015 11:48 am ET

More than a decade of research is paying off for Battelle Memorial Institute in the form of Geon BIO PVC compounds from PolyOne Corp.    More

Image

California may require more recycled content in bottles

April 24, 2015 11:16 am ET

California lawmakers are considering a pair of bills that would bump up the required recycled content in plastic bottles for beverage companies to...    More

Image

KHS cuts packaging with direct printing on PET bottles, adhesive multi-packs

April 23, 2015 1:39 pm ET

KHS GmbH has been pouring a lot of time into solving issues related to direct printing on PET bottles, and after eight years of work, everyone...    More

Image

DuPont center in India gets LEED Certification

April 23, 2015 1:07 pm ET

DuPont Co.'s Knowledge Center in Hyderabad, India, was awarded LEED certification by the U.S. Green Building Council.    More

Image

MeadWestvaco joins the Recycling Partnership

April 23, 2015 11:19 am ET

MeadWestvaco Corp., a global packaging company with some operations in plastics, is joining the Recycling Partnership.    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 15, 2015 - September 17, 2015Plastics Caps & Closures - September 2015

More Events