Henniges touts ability to cut weight from seals

Allison Strouse

Published: January 15, 2013 6:00 am ET

Related to this story

Topics Automotive, Sustainability, Pipe/Profile/Tubing

AUBURN HILLS, MICH. (Jan. 15, 11:30 a.m. ET) — Henniges Automotive Holdings Inc. has found ways to cut anywhere from eight to 12 pounds from vehicle weight through sealing alone.

“Our product has often been overlooked in the area of weight,” CEO Douglas DelGrosso said. “People focus on typically metal and steel to get weight off and if you think about the amount of sealing that is in the typical C-Class sedan, it’s a lot of product and rubber is heavy.”

In an environment fueled by meeting such standards as fuel efficiency and emissions reductions, being able to take weight off a vehicle wherever possible helps.

“If you find some creative ways to take off weight and take it to the customer in today’s environment with all the pressure that’s on them to meet, whether its CO2 standards or general emissions standards, we have tried to focus ourself there,” he said.

DelGrosso sees this as a big opportunity for his firm if it is able to show its customers the potential for such reductions.

“That’s a pretty significant amount of savings [in weight],” he said. “That represents about a 20-percent reduction in the overall weight. ... Some of it can be done without any additional costs.”

If done on a large enough scale, he added, it might even amount to a cost savings.

Going with plastic over rubber has been the answer in the past on occasion, according to Steve Murree, Henniges director of advanced product and process development. To help reduce the mass of the products, eliminating materials like rubber and metal have helped.

While the push for this mainly is coming from Henniges, the executives said there have been a few customers coming to the auto supplier looking for a solution.

“Each customer has their traditional way of engineering sealing,” DelGrosso said. “This is where we can be that catalyst.”

Looking over what the best practices and procedures are, he said this was the firm’s chance to approach its customers and say here is the best way to accomplish weight reduction.

“We can be in that eight- to maybe 11-pound range,” DelGrosso said.

“I think that requires a certain level of push from us. Not all [car makers] are out there doing those teardowns to get that type of data [on reducing weight in sealing].”

Getting the information to their customers isn’t the hard part though.

“One of the struggles is that the working level, their objective is to launch vehicles without issues,” Murree said. While they like the push from the company, lessening the weight and coming up with alternatives for sealing are not among their main objectives.

“We have to start attacking higher up and having them push it down as an objective,” he said.

Issues like fuel efficiency are not expected to go away anytime soon.

“What we are trying to do is be ahead of that because we can, and be there as a good value supplier and say we have some ideas that you didn’t traditionally look at for this product,” DelGrosso said.


Comments

Henniges touts ability to cut weight from seals

Allison Strouse

Published: January 15, 2013 6:00 am ET

Post Your Comments


Back to story


More stories

Image

LiquiForm looks to fundamentally change blow molding process for bottles

March 5, 2015 12:13 pm ET

Those in the know are lifting the veil, just a bit, on fledgling technology being developed that would fundamentally change the way plastic bottles...    More

Image

Plastics News Now: Plastic raises the roof

March 5, 2015 8:44 am ET

Toyota's hydrogen fuel cell vehicle gets an assist from carbon fiber, slate roof shingles get the plastic treatment and West Coast port delays had...    More

Image

Bigger doors, windows gain appeal

March 5, 2015 11:43 am ET

Door and window manufacturers are continuing to super-size product lines to make a grander first impression at main entrances and to expand vista...    More

Image

'Listen to the Science' ads a start, but consumers still need education

March 5, 2015 11:36 am ET

Since joining Plastics News — and therefore learning more than the average consumer about the business and science of plastics — there...    More

Image

Auto supplier Motus adds more production as it buys Leon Interiors

March 5, 2015 10:52 am ET

Motus Integrated Technologies, a Tier 1 automotive interiors supplier, is getting bigger, adding the assets of Tier 2 supplier Leon Interiors Inc.    More

Market Reports

Flexible Packaging Trends in North America

North America represents about 30 percent of the global consumption of flexible packaging. Annual growth in this region is forecast at 4 percent during the next 5 years.

For more insight on growth opportunities, drivers of growth and the outlook for 2015, download this report.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 billion plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Upcoming Plastics News Events

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events