Purac develops high heat-resistant polylactic acid resin

Published: February 26, 2013 4:01 pm ET
Updated: February 26, 2013 4:04 pm ET

Related to this story

Topics Materials, Materials Suppliers

ATLANTA — Bioplastics firm Purac has developed a high heat-resistant blend of polylactic acid that it says will open up new markets for bioplastic products.

Purac developed its high-heat PLA by utilizing sterochemically pure PLA homopolymers. By combining the different polymers that make up PLA in different ways, Purac can create resin with a range of improved properties, like the ability withstand temperatures up to 356° F.

The Purac technology allows for the development of PLA that can be used as a replacement for polystyrene, polypropylene and ABS, said Francois de Bie, marketing director for bioplastics at Purac, in a presentation at the 2013 Packaging Conference.

Purac says its PLA is made from renewable raw materials, has a reduced carbon footprint, and is biodegradable.

The high-heat PLA is currently being used in several commercial applications, including injection molded food service ware – plates, bowls, cups and utensils.

The containers are food contact approved, can be used in the microwave and dishwasher, and are heat resistant up to 100° C, so they can hold hot coffee or tea, de Bie said.

Purac has also had interest from consumer goods companies who want to use the material in luxury goods and appliances, among other applications, he said. PLA in those applications could have heat resistance up to 120° C for a short period and would be 100 percent bio-based.

High-heat PLA can also be used in place of polystyrene in disposable coffee cups. Using PLA does not require new equipment or processes and the line runs at the same speed when converting PLA as it does when converting polystyrene, de Bie said.

PLA is still more expensive than polystyrene, but being able to run at the same speed lessens the impact, he added.

The material can also be used to make injected molded preforms that are then blow molded into reusable water bottles or baby bottles. The bottles are not transparent, but the heat resistance means they can withstand boiling water and can be steam sterilized, an important consideration for baby bottles, he said.

Purac has also developed PLA foam that looks and feels identical to expanded polystyrene, he said.

The foam has high impact resistance and similar properties to PS and can be used in packaging materials, but cannot currently be used to make foam coffee cups, he said.

Purac is currently developing a transparent high-heat biaxially oriented PLA film. The film could be used to replace biaxially oriented polypropylene films, and has similar tensile and barrier properties to standard PLA films but with a high melting point of 220-250° C, de Bie said.

Purac, based in Gorinchem, the Netherlands, is a subsidiary of bakery products company CSM NV.

The Packaging Conference was held Feb. 4-6 in Atlanta.


Comments

Purac develops high heat-resistant polylactic acid resin

Published: February 26, 2013 4:01 pm ET
Updated: February 26, 2013 4:04 pm ET

Post Your Comments


Back to story


More stories

Image

Sony entering recycled PC market

August 27, 2014 11:08 am ET

Consumer electronics giant Sony Corp. is getting into a sideline of selling recycled resins.    More

Image

Nova expanding PE research center

August 26, 2014 1:36 pm ET

Nova Chemicals Corp. has broken ground on an expansion of its polyethylene research center in Calgary, Alberta.    More

Image

Sinopec licenses PP technology to USA, posts half-year results

August 26, 2014 11:46 am ET

China's state-owned petrochemical giant Sinopec Corp. said it is licensing polypropylene polymerization technology to a U.S. plant for the first time ...    More

Image

Japan's DIC planning PPS compounding plant in China

August 25, 2014 1:28 pm ET

Japanese materials firm DIC Corp. plans to open its first polyphenylene sulfide (PPS) compounding plant in China by the end of 2015.    More

Image

China's PVC exports face challenges

August 22, 2014 2:14 pm ET

Despite robust growth in the first half of the year, China's PVC exports now faces new challenges, due to trade barriers and new capacity ramping up i...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events