California updates container law to encourage more recycled content

By Gayle S. Putrich
Staff Reporter

Published: March 1, 2013 3:21 pm ET
Updated: March 1, 2013 3:28 pm ET

Related to this story

Topics Packaging, Sustainability, Public Policy, Materials, Recycling, Government & Legislation

WASHINGTON — After more than 18 years on the books, changes to California's rigid plastic packaging container (RPPC) regulations for 2013 mean the law will finally be able to do what it was meant to: increase the amount of post-consumer recycled material that goes into packaging sold on California stores' shelves.

State regulators say the changes not only clarify the law and make it easier for product manufacturers to follow, they also open the door for easier communication and partnership between the state, the product manufacturers and the plastic packaging manufactures.

"It was really about listening to the industry and trying to get program consistency," said CalRecycles' Trevor O'Shaughnessy, section manager for RPPC.

Previously, regulations excluded a container if it could not be sealed more than one time, causing confusion and leaving out different types of containers that did or held the same thing. As of Jan. 1, the first time a container is sealed counts as "one time," including heat-sealed clamshell packaging, which is now counted and regulated as RPPC in California.

Buckets were just one of many oddities under the original law, with those with a metal handle excluded from the RPPC program because they were not all plastic. Now buckets and pails with and without plastic handles are all are considered "equal products."

The new regulations explicitly spell out for the first time that resin switching is not permitted as a way to get around the law. But they also stipulate that using a 25 percent post-consumer resin or a 10 percent source reduction are among ways to bring a package into compliance. Regrind, however, does not count toward the post-consumer percentage.

Perhaps the biggest change, O'Shaughnessy said, is the implementation of a three-step notification system for product makers.

The first step is registration for product makers selling their products in California. Registration is available on CalRecycles' website and product manufacturers can sign up on their own or wait to be notified by the state.

Second is pre-certification, where the department will notify a select pool of the registered product manufacturers that they could be evaluated, the first round of which will go out in April. Those firms can determine if their RPPCs are compliant using online tools, or request an advisory opinion, O'Shaughnessy said, where regulators will look at their packaging, determine if it falls under the regulations' purview and if it is compliant.

One year after the pre-certification phase comes step three, compliance certification, where groups selected from the pre-certification pool will be asked to report on all of their containers' compliance.

"Through our rulemaking, the department heard a lot of the concerns from the collective industry — the container manufacturers and product manufacturers — about getting enough notice and awareness for those working in national markets that may not have been aware of the original law," O'Shaughnessy said. "So we developed the phased-in system for better awareness. Before you're selected, you're registered, you're pre-certified. Nothing is getting sprung on anyone."

Non-compliance means a fine of up to $100,000 per year for the product makers for any and all phases of the three-step process. And while the measure is primarily focused on the product manufacturer, there is some compliance burden for packagers.

"The responsible party is the product manufacturer that puts the product into the RPPC container," O'Shaughnessy said. "If we find [the product manufacturer] non-compliant and that non-compliance is due to the container manufacturer, the penalty can absolutely go to the container manufacturer.

"But the burden is on the product manufacturer. They should be getting documentation about recycled content in the packaging from the package manufacturer."

And if several product manufacturers are found in violation of the RPPC law and are all using the same container maker, that would raise a red flag, O'Shaughnessy said, and could result in a fraud case against the container maker, which would be in the hands of the California state attorney general.

He stressed that container manufacturers are not regulated under the law, but that the new three-step system and the Internet provide a window into the process for the plastics industry that was not available under previous versions of the regulations.

"With these new Web tools, now it's a little simpler to outreach to container manufacturers. We will never, under the existing California law, produce a list of complainant container manufacturers. We never evaluate a container manufacturer," he said. "They are not regulated by us, but they can go to our website and they can register and that way they'll get information on workshops, get on the email list … they can participate and hear what's going on, be informed and join the conversation. And we, as regulators, will be better able to hear their input."

Laura Stewart, vice president of sales and marketing at Madison, Wis.-based thermoformer Placon Corp., said that for the most part, product makers tend to be out in front of the push for higher recycled content in packaging, though she said California is the only state with that type of legislation that she is aware of.

Placon had customers as early as the late 1980s and early 1990s coming to it looking to use recycled PET in their packaging, particularly when selling to national chain retailers such as Wal-Mart, which was making an effort to have recycled content in packaging on its shelves.

"We've been not so much driven by the regulations as by customer needs," she said. Customer need has been so great that in addition to thermoforming, Placon has its own closed-loop facility for washing and regrinding post-consumer bottles and thermoform packaging for processing.

Placon's EcoStar line, launched two years ago, offers up to 100 percent post-consumer-recycled PET and serves as an example of how much has changed in plastic packaging since California first enacted its RPPC law in the early 1990s.

"If you were making a rigid plastic container 15 years ago, there were not a lot of options for the manufacturers," said Mark Murray, executive director of Californians Against Waste, which helped push for the initial legislation and has been disappointed in its "weak and spotty" enforcement over the years. "It used to be that the excuse was, 'I don't know how to get a hold of that much recycled material.' But now it's a fairly robust global marketplace, and it's not even cost-prohibitive anymore. You can get recycled feedstock pretty cheap, especially non-food-contact stock."

Placon's Stewart said the key for plastics processors and packagers is to stay flexible.

"We tend to be very market-focused, so we're looking at what our customer needs are and what their customers' needs are. The market will find the equilibrium on recycled content," she said.

Placon also works with smaller product manufacturers that might not have the engineering staff to work out compliance issues with the California law.

"Virgin [amorphous] PET to post-consumer recycled is a very easy switch. There's often a misconception about price with smaller companies or some aesthetic qualities to be worked out. But there shouldn't be a negative associated with recycled content," she said.


California updates container law to encourage more recycled content

By Gayle S. Putrich
Staff Reporter

Published: March 1, 2013 3:21 pm ET
Updated: March 1, 2013 3:28 pm ET

Post Your Comments

Back to story

More stories


Major packaging merger includes plastics operations

January 26, 2015 12:24 pm ET

A merger of packaging companies MeadWestvaco Corp. and Rock-Tenn Inc. will create a new company with nearly $16 billion in annual sales.    More


MonoSol optimistic it can reach new markets with water soluble films

January 26, 2015 4:46 pm ET

MonoSol LLC — riding a wave of growth spurred on by the rapid adoption of water soluble detergent packets in recent years — is looking to ...    More


Auto industry on the hunt for new lightweight materials

January 26, 2015 4:03 pm ET

The auto industry is focusing on lightweighting, and this is igniting a race to find new materials that can meet ever-changing performance needs of...    More


Material Insights: PP production issues, preparing for NPE

January 26, 2015 1:38 pm ET

Production problems in Texas add more complication for polypropylene, Entek has new equipment ready to show compounders at NPE and we take a look...    More


Continental builds low-emission interior trim factory in China

January 26, 2015 12:33 pm ET

Benecke-Kaliko AG is making the largest investment in its history to build an environmentally friendly auto interior trim plant in China, prompted by ...    More

Market Reports

Plastics in Automotive: Innovation & Emerging Trends

This special report newly released by PN and sponsored by The Conair Group examines current trends in the use of plastics in automotive, materials innovations and the changing landscape. It includes a review of legislative/regulatory activity impacting vehicle development and lightweighting, market opportunities & challenges for mold and toolmakers, innovative design strategies being implemented by major OEMs and suppliers, as well as a review of key indicators in Canada, Mexico, Brazil and China.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Upcoming Plastics News Events

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events