Asthma rates below average in US flexible foam plants

URETHANES TECHNOLOGY INTERNATIONAL

Published: March 5, 2013 8:58 am ET
Updated: March 5, 2013 9:01 am ET

Related to this story

Topics Materials, Materials Suppliers

LOUDON, TENN. — A report sponsored by the U.S. Polyurethane Foam Association, concentrating on the country's larger flexible polyurethane foam plants, has found that asthma is lower at these plants than in the general population.

The data, presented during a Polyurethane Foam Association Technical Program in Loudon, Tenn., suggests that workers in the plants which were surveyed were well protected from exposure by training and control technology.

Information was gathered at plants accounting for 90 percent of PU flexible foam production over a 24 year period. The data was collected and analyzed by a law firm based in Washington, DC, McIntyre & Lemon pllc.

The survey includes two sets of data from 1988-2007 and 2008-2011. The 2008 survey provided historical data on more than 1300 workers in 23 manufacturing sites; the 2012 update polled 1037 workers in 38 plants.

The report abstract said:

The results indicated that the incidence of self-reported occupational asthma was infrequent representing less than 1 percent of the related worker population. Medically confirmed cases were less frequent. In fact, no medically confirmed cases of occupational asthma were reported among the 23 responding FPF production plants during the five years prior to the survey.

Read the abstract of the report "TDI Emissions and Exposure Monitoring and Control in Flexible Slabstock Plants: A 20-Year History of Safety" by Lynn Knudtson, Polyurethane Foam Association.

http://www.pfa.org/abstracts/aboct08.html


Comments

Asthma rates below average in US flexible foam plants

URETHANES TECHNOLOGY INTERNATIONAL

Published: March 5, 2013 8:58 am ET
Updated: March 5, 2013 9:01 am ET

Post Your Comments


Back to story


More stories

Image

Material Insights: Nova Chemicals breaks ground for PE research

September 2, 2014 1:06 pm ET

Polypropylene prices climb 5 cents, Nova Chemicals expanding research center and Sinopec licenses technology to a U.S. plant.    More

Image

Startup post-consumer recycling specialty company Zzyzx wins grant

September 2, 2014 1:33 pm ET

An Allentown, Pa., company is receiving a grant of $737,000 to help support its efforts to develop polymers using post-consumer plastics.    More

Image

A. Schulman buys Australia's Compco, 10th acquisition in 4 years

September 2, 2014 11:13 am ET

Akron, Ohio-based A. Schulman Inc., a supplier of high-performance plastic compounds and resins, said it has acquired a company near Melbourne,...    More

Image

EPA fines RI polymer company

August 29, 2014 1:20 pm ET

A Rhode Island polymer manufacturer has reached a $60,000 settlement with the U.S. Environmental Protection Agency (EPA) for violating federal clean...    More

Image

Tighter resin prices leading to price hike for PE film

August 29, 2014 11:13 am ET

One of North America's largest film makers is pushing through a polyethylene price increase due, in part, to the tight resin market.    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events