GM puts cars on strict diet: Lighter materials keys to effort

By David Sedgwick
AUTOMOTIVE NEWS

Published: March 18, 2013 12:36 pm ET
Updated: March 18, 2013 12:45 pm ET

Image By: General Motors Dan Akerson

Related to this story

Topics Automotive, Sustainability
Companies & Associations General Motors Co.

DETROIT — When General Motors CEO Dan Akerson vowed earlier this month to cut the weight of new models 15 percent by the 2016 model year, he put his engineers on a rigorous schedule.

Is it doable? Yes, but it's a stretch, says one knowledgeable industry consultant.

"It will be a big effort," said Richard Schultz, managing director of Ducker Worldwide in suburban Detroit, an adviser on mass reduction to GM and other automakers. "That's a lot of work, and GM doesn't have a lot of time."

For instance, GM would have to shed about 600 pounds from a V-6-powered large sedan such as the Buick LaCrosse, which weighs 4,045 pounds.

Engineers could save as much as 200 pounds by substituting a four-cylinder engine for the V-6. The rest would come from lightweight materials.

Schultz said GM will avoid large amounts of carbon fiber reinforced plastic, and it is unlikely to introduce an aluminum-bodied car, as Audi and Jaguar have done.

Instead, GM will use:

  • More high-strength steel for the body-in-white.
  • Magnesium for selected parts such as transmission cases.
  • More aluminum for doors, decklids, hoods and structural parts.

Like other CEOs, Akerson doubtless feels a sense of urgency to meet federal corporate average fuel economy standards, which rise to 35.5 mpg by the 2016 model year.

In his Houston speech last week, Akerson hinted at GM's intention to use more aluminum and high-strength steel.

GM has begun using spot welding to attach aluminum to the body-in-white, saving money and weight by eliminating rivets, which can add as much as two pounds to a car's weight.

The new spot welding system disrupts the oxide on the surface of an aluminum component, ensuring a stronger weld than before. That, in turn, eliminates the need for rivets, GM says.

GM offered a glimpse of the technology's potential with the 2014 Chevrolet Corvette Stingray, company spokesman Dan Flores said.

Spot welding "allows engineers to look for more innovative ways to use aluminum beyond traditional uses" such as hoods, decklids and doors, Flores said.

Translation: Look for GM to use a lot more aluminum in structural components in the body-in-white.

GM also hopes to save money by introducing a high-strength steel that is under development. Last year, GM said it had invested in NanoSteel Co. of Providence, R.I., which has developed a nano-structured steel alloy.

Automakers like high-strength steel because they can make parts thinner, saving weight. But typically, steel alloys must be hot-stamped, which raises manufacturing costs.

NanoSteel is developing a high-strength steel that would be cold-stamped, at less cost.

"If it's cheaper, you can use more of it," Flores said. "It's still in trial, but that's where we think the competitive advantage is."

While GM is investing in aluminum and high-strength steel, one might argue that the company is still hedging its bets.

Take the 2014 Chevrolet Silverado pickup, which goes on sale this spring. GM says it cut 59 pounds by using an aluminum hood, front control arms and steering knuckles. It also used high-strength steel for two-thirds of the cab structure.

But GM could have saved more weight by introducing an aluminum cargo box, cab or bumpers. Mark Reuss, president of GM North America, has noted that fuel-conscious buyers can opt for the Chevrolet Colorado compact pickup.

But Schultz speculates that GM will work harder to cut the weight of its next-generation Silverado. "Why spend the extra money until you have to?" Schultz asks.

What about more exotic materials such as carbon fiber reinforced plastic? The Corvette features a carbon fiber hood, but this material is still too expensive for mass-market vehicles.

To cut cost, GM formed a partnership in 2011 with Teijin Ltd., a Japanese producer of carbon fiber. The company has opened a technical center in suburban Detroit to develop a cheaper way to manufacture carbon fiber reinforced thermoplastic.

Carbon fiber weighs one-fourth as much as conventional steel and is 10 times stronger. But it takes a long time for the resin to set in the mold.

Teijin is trying to reduce the cycle time required to produce carbon fiber parts to less than a minute. But that technology isn't ready, Flores said.

Because carbon fiber is not ready for prime time, that leaves aluminum and high-strength steel as the materials of choice -- especially for a vehicle's front end.

Look for engineers to use more aluminum hoods, bumpers, suspension components and possibly engine cradles.

But GM "is not going to use any technology that they are not already comfortable with," Schultz said. "Everything is happening just a little bit faster, but it's something they know how to do."


Comments

GM puts cars on strict diet: Lighter materials keys to effort

By David Sedgwick
AUTOMOTIVE NEWS

Published: March 18, 2013 12:36 pm ET
Updated: March 18, 2013 12:45 pm ET

Post Your Comments


Back to story


More stories

Image

Simple lightweighting in packaging, caps not so simple anymore

October 22, 2014 4:16 pm ET

The days of finding simple ways to remove additional weight — and costs — from plastic bottles are over, according to one expert.    More

Image

Ford's final ACH plant, injection molder of HVAC systems, to close

October 22, 2014 1:58 pm ET

Ford Motor Co. will shed the last line of business in 9-year-old Automotive Component Holdings LLC by December when ACH closes its Plymouth, Mich.,...    More

Image

Unilever uses foaming in new bottle

October 22, 2014 1:35 pm ET

Foaming is a good alternative to thin-walling for reducing plastic use in consumer goods packaging, according to a Unilever plastics expert.    More

Image

Bioplastics, design join forces for SOMA

October 21, 2014 11:33 am ET

A polylactic acid made by Germany's Fraunhofer UMSICHT is a key part of the Soma home water filtration system, which its developers call the...    More

Image

BASF targets coffee and automotive connoisseurs with new resin grades

October 21, 2014 2:07 pm ET

BASF SE is using polybutylene terephthalate (PBT), which is normally used to manufacture high-end electronics, in a food consumer packaging product.    More

Market Reports

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our analysts provide insight on business trends, foreign investment, top end markets and plastics processing activity. The report also provides important data on exports, production, employment and value of plastics products manufactured.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events